Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM623: Can eMMC0 support DDR50 mode

    Part Number: AM623 Tool/software: Can MMC0 port support eMMC DDR50? In the datasheet, list only 3 modes for eMMC application. DDR50 in SD Card application but not for eMMC. Although list all features in TRM, but we was told follow datasheet…

  • [FAQ] How to flash u-boot to GPMC-NAND with USB-DFU on AM62x

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62-LP Tool/software: AM62x boot ROM supports booting from parallel GPMC NAND. From "5.4.9.1 GPMC NAND Bootloader Operation" in AM62x TRM "GPMC NAND boot only supports boot from ONFI 1.0 compatible…

  • [FAQ] SK-AM64B: What is the purpose of --operation=flash-phy-tuning-data ?

    Part Number: SK-AM64B Tool/software: Greetings All, In MCU PLUS SDK offering, across Sitara SoCs, one must have come across different configuration files. These configuration files are located inside the directory: MCU_PLUS_SDK_INSTALL_PATH\tools…

  • [FAQ] AM69A: BOOTING FROM EMMC WITHOUT SD CARD

    Part Number: AM69A Other Parts Discussed in Thread: AM69 Tool/software: How to boot from eMMC without SD card?

  • [FAQ] PROCESSOR-SDK-AM64X: Undeclared Identifier for MCU GPIO Interrupt Routers

    Part Number: PROCESSOR-SDK-AM64X Other Parts Discussed in Thread: SYSCONFIG Tool/software: I am trying to upgrade my project to use the new MCU+ SDK 10.1 and I'm running into a compilation error saying that the interrupt router number is undeclared. This…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62Px / AM62D-Q1 / AM62L / AM64x / AM243x (ALV) / AM335x Design Recommendations / Custom board hardware design - Schematics review checklists

    Part Number: AM625 Other Parts Discussed in Thread: AM62D-Q1 , AM62L Tool/software: Hi Board designers The AM64x, AM62x, AM62Ax, AM62D-Q1, AM62Px and AM62L custom board Schematic review Checklist application note provides a supplemental design check…

  • [FAQ] AM62A7-Q1: Deploy MMYOLO on AM62A, YOLOV8 nano as example.

    Part Number: AM62A7-Q1 Tool/software: MMYOLO is an open source repo for quick yolo model evaluation. Deployment MMYOLO on TI processor like AM6x or TDAx requires some modifications on this repo. This FAQ uses yolov8 as example to demonstrate how to…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62A / AM62P / AM62D-Q1 / AM64x / AM243x Design Recommendations / Custom board hardware design - Queries related to SysConfig-PinMux IOSET and Voltage Conflict

    Part Number: AM62P Tool/software: Hi TI Experts, I see IOSET option and Voltage Conflict indication while using SysConfig-PinMux. Can you provide additional inputs on the IOSET and Voltage configuration

  • [FAQ] SK-AM64B: Incorrect auto-generated MAC port 2 PHY configuration

    Part Number: SK-AM64B Other Parts Discussed in Thread: DP83869 , SYSCONFIG Tool/software: The two Ethernet Ports on SK-AM64x are connected to two separate Gigabit Ethernet PHY Transceivers DP83867. On enabling MAC Port 2 in SK-AM64x networking…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62A / AM62P / AM62D-Q1 / AM64x / AM243x Design Recommendations / Custom board hardware design - Queries related to passive components values, tolerance, voltage rating

    Part Number: AM625 Tool/software: Hi TI Experts, 1. In the SK/EVM i see 49.9K resistor used. Can i use a standard value instead 2. In the SK/EVM i see a number of resistors used with 1% tolerance for pullups and series resistors. Can i use standard…

View FAQ threads
  • Threads 198451 Discussions