Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: Reconfiguration of disconnected camera or camera that is powered off

    Part Number: TDA4VM How to reconfigure the disconnected camera or if the camera is powered off during the execution of Multi-cam demo?

  • [FAQ] AM6442: AM6442 SD card interface

    Part Number: AM6442 hi, I was referring to Starter kit Schematic and EVM schematic of AM6442, I would like to know the reason for having Switched power rail which is enabled based on reset status for SD card interface. I had done the same Circuit…

  • [FAQ] AM62X/AM64X : [FAQ] Debugging SBL boot in RTOS SDK

    Hello Team, I was trying to boot the EVM via SBL NULL/SBL OSPI , but it does not work. Can you please let me know the steps for debugging SBL? Thanks

  • [FAQ] J721S2XSOMXEVM: Backporting Patches for TIDL From 9.0 to 8.6 SDK for J721S2

    Part Number: J721S2XSOMXEVM This are patches for backporting tidl software layer from 9.0 SDK to 8.6 SDK. Please refer this FAQ to download and apply patches, the detailed documentation is available soon as part of App Note, and will be linked here…

  • [FAQ] J784S4XEVM: Backporting Patches for TIDL From 9.0 to 8.6 SDK for J784S4

    Part Number: J784S4XEVM This are patches for backporting tidl software layer from 9.0 SDK to 8.6 SDK. Please refer this FAQ to download and apply patches, the detailed documentation is available soon as part of App Note, and will be linked here. Please…

  • [FAQ] J721EXCPXEVM: Backporting Patches for TIDL From 9.0 to 8.6 SDK for J721E

    Part Number: J721EXCPXEVM This are patches for backporting tidl software layer from 9.0 SDK to 8.6 SDK. Please refer this FAQ to download and apply patches, the detailed documentation is available soon as part of App Note, and will be linked here. …

  • [FAQ] AM62A3: MCU_OSC0 clock speed options

    Part Number: AM62A3 Hi all, the AM62A datasheet shows a typical value of 25MHz for the crystal on MCU_OSC0 and no mention of additional clock speed modes. The TRM in Fig 6-84 shows 24/25/26MHz options for the main crystal. Are 24MHz and…

  • [FAQ] J721S2XSOMXEVM: PCIe hardware limitation for J721S2/TDA4VL with TI EVM

    Part Number: J721S2XSOMXEVM Other Parts Discussed in Thread: TDA4VL , TDA4VM When using J721E/TDA4VM with TI's CPB (common processor board), all PCIe slots are functional. However, when I switch to J721S2/TDA4VL SOM board and use the same CPB, only…

  • [FAQ] AM6442: 1Gbps ethernet phy which can support both copper and OFC cables

    Part Number: AM6442 Other Parts Discussed in Thread: DP83869 Hi Team , we are developing a hardware based on AM6442ASFGGAALV. We have following initial queries .Please help We need a 1Gbps ethernet phy which can support both copper and OFC cables…

  • [FAQ] SK-AM68: How do I run the core-image-weston on SK-AM68?

    Part Number: SK-AM68 I want a minimal configuration to run graphics applications using Weston since the full SDK image is not necessary for the development of my application. Currently, when I try to boot the core-image-weston as is from the Yocto build…

View FAQ threads
  • Threads 197994 Discussions