Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VH-Q1: Testing functionality of ring accelerator

    Part Number: TDA4VH-Q1 Hi, Could you please guide us on method to inject error on ring accelerators.Thank you.

  • [FAQ] TDA4VEN-Q1: C7x reset from CCS issues double page Fault

    Part Number: TDA4VEN-Q1 Trying to reset c7x through CCS issues a double page fault.

  • [FAQ] AM625: OSPI Access Across Different Cores

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , AM62L On different TI SITARA MPU SoCs, lets have a look at SoC wise cores which have access to the OSPI module/Controller in the current MCU+ SDK Software offering. Please refer the table below…

  • [FAQ] AM625: How to configure Timer in Interrupt mode

    Part Number: AM625 Other Parts Discussed in Thread: SYSCONFIG Lets have a look at the implementation of application using a TIMER module(DM TIMER) in Interupt mode of operation. The application code can be used as it is or as a baseline for configuring…

  • [FAQ] AM62D-Q1 Custom board hardware design – AUDIO-AM62D-EVM Audio Functionality Implementation Related Queries and Design Notes

    Part Number: AM62D-Q1 Other Parts Discussed in Thread: AUDIO-AM62D-EVM Hi TI experts, I am planning to reuse the AM62D-Q1 AUDIO-AM62D-EVM schematics for my custom board design. I see the below schematic sections (pages) added to the AUDIO-AM62D-EVM…

  • [FAQ] AM6421: RESETSTATz output during ROM boot

    Part Number: AM6421 Hello, During a successful QSPI boot, I have captured the following signals: MCU_PORz, RESETSTATz, OSPI_CLK, OSPI_CS. I'm observing that roughly 35mS after RESETSTATz goe high it has a 160uS period where it drops low. Looking at…

  • [FAQ] TDA4VH-Q1: How to configure the SerDes lane for PCIe, USB, Ethernet, and Display in Linux?

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH The high speed interfaces on the TDA4x share the SerDes lanes. The lanes can be muxed for different interfaces, but how can I configure them within Linux?

  • [FAQ] AM2754-Q1: Working Configurations for 8S-8S-8S on S28HS512T Serial NOR OSPI Flash

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: SYSCONFIG In MCU+ SDK 11.02, the OSPI and Flash examples are configured by default to operate at the highest protocol: 8D-8D-8D. For configuring 8S-8S-8S SDR Protocol on S28HS512T Serial NOR OSPI…

  • [FAQ] TDA4VH-Q1,TDA4VE,TDAVAL,TDA4VL,TDA4VP-Q1,TDA4AP-Q1: How to reset C7x and load binary faster via CCS

    Part Number: TDA4VH-Q1 Hi, After reset of C7x, i am trying to load newer C7x binary, but the second load takes a lot of time. Could you please help me to solve this issue.

  • [FAQ] AM64/AM243: Facing an issue with CCS when trying to flash an image using SBL JTAG UNIFLASH

    Part Number: AM6442 Other Parts Discussed in Thread: UNIFLASH I am trying to flash an image for AM64/AM243 device by loading SBL JTAG UNIFLASH from CCS version 20. *.* , after following the steps mentioned in the MCU+SDK documentation: https://software…

View FAQ threads
  • Threads 202321 Discussions