Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM62P / AM62P-Q1 Custom board hardware design – I2C interface

    Part Number: AM62P Other Parts Discussed in Thread: AM62A7 , , AM6442 , SK-AM64B Hi TI Experts, I have the below queries regarding the I2C interface: Need information on the number of I2C interfaces available. Termination of I2C interfaces when…

  • [FAQ] AM62P / AM62P-Q1 Custom board hardware design – Collaterals to Get started

    Part Number: AM62P Other Parts Discussed in Thread: , AM62D-Q1 , , SYSCONFIG Hi TI Experts, Can you provide a List of collaterals that can be referred when starting a custom board hardware design.

  • [FAQ] PROCESSOR-SDK-AM57X: What IPC version for do I use when using Linux SDK 08.02.01.00?

    Part Number: PROCESSOR-SDK-AM57X Utilizing the correct version of IPC will help your IPC applications function correctly. One key point is that one cannot mix and match SDK RTOS versions with different Linux SDK versions. The Linux kernel remoteproc…

  • [FAQ] AM6442: ADC0_DIG_TEST[0-7]. when a digital inputs, can these eight be considered as MAIN GPIO and/or interrupt inputs at 1.8V logic

    Part Number: AM6442 We are opting to not use the ADC module for ADC conversion. Per the TRM document SPRUIM2G section 12.1.1.4.2.2 we want to set GPI_MODE_EN = 1. Can these 1.8V logic level inputs we used either as interrupts to the A53 or R5 cores…

  • [FAQ] SK-AM68: How can I get started with streaming H264/H265 from a camera input

    Part Number: SK-AM68 I am trying to get started streaming from a camera input to display on my host machine. Are there any steps to get started?

  • [FAQ] AM62A7: How to Use the ISP on AM62A

    Part Number: AM62A7 I want to develop camera applications on AM62A. My camera is a raw camera. How can I use the ISP on AM62A for my application?

  • [FAQ] AM6442: Rise/Fall time requirement for RGMII(0.75ns)

    Part Number: AM6442 Other Parts Discussed in Thread: DP83867E , DP83869HM , TMDS64EVM Hi team, I'm asking same question on interface forum. But I need help from Sitara team as well because it seems related to drive strength for RGMII of AM6442. …

  • [FAQ] AM62A7: What's the maximum camera resolution and frame rate supported by AM62A

    Part Number: AM62A7 I want to use a specific sensor on AM62A. What is the maximum camera resolution and frame rate supported by AM62A?

  • [FAQ] SK-AM69: Booting from OSPI

    Part Number: SK-AM69 Other Parts Discussed in Thread: AM69 I followed the steps on Processor SDK Linux for AM69 to boot from OSPI on SK-AM69 and I see the following message upon boot: U-Boot SPL 2023.04-g756ba776d4 (Jul 13 2023 - 05:36:12 +0000) EEPROM…

  • [FAQ] AM62A7: How to Set the Minimum/Maximum Exposure Time and Analog Gain for 2A Algorithm?

    Part Number: AM62A7 I’ve just brought up a sensor for AM62A. Now I’m going to start image quality tuning. According to the AM6xA ISP Tuning Guide , the first thing is to set the minimum and maximum exposure time and analog gain for the 2A algorithm. …

View FAQ threads
  • Threads 197946 Discussions