Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VE-Q1: SBL HLOS Boot Test Procedure for Combined AppImage

    Part Number: TDA4VE-Q1 Hi, Is there a recommended procedure to run an HLOS on the A72 cores while running firmware on the R5 and DSP cores?

  • [FAQ] Binary blob authentication and decryption using TIFS on AM62x

    Part Number: AM625 SYSFW/TIFS supports binary blob verification and decryption on AM6xx family SoC (HS-SE). https://software-dl.ti.com/tisci/esd/latest/6_topic_user_guides/authentication.html The FAQ lists how to call the TISCI API TISCI_MSG_PROC_AUTH_BOOT…

  • [FAQ] TDA4AH-Q1: How to Generate an Assembly file and perform analysis

    Part Number: TDA4VH-Q1 Hi Team, How can I generate an assembly file from C7x code and calculate the total cycle count using the software pipeline information found in the assembler file? Regards, Betsy Varughese

  • [FAQ] AM2754-Q1: [FAQ] Mcasp signal placement order in buffer for multiple serializers and multiple channels/slots

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: SYSCONFIG , TAD5212 Mcasp buffer order To be short, in case of multiple serializers used in one Mcasp, the samples are placed interleaved by slot not frame by default. (Please check the "12.1…

  • [FAQ] J722SXH01EVM: How do I use the Fusion2 board with the J722SXH01EVM

    Part Number: J722SXH01EVM Tool/software: How do I use the Fusion2 board with the J722SXH01EVM ? When I try to run the single camera demo, I see the following error: [MCU2_0] 76.844004 s: Error writing 0x01 to de-serializer(0x3d) register 0x4c…

  • [FAQ] TDA4VH: TIMER in Capture Mode.

    Part Number: TDA4VH Tool/software: How to enable TIMER in Capture mode in Linux ?

  • [FAQ] TDA4VH-Q1: How to create openvx graph with a node that needs data from the next node

    Part Number: TDA4VH-Q1 Tool/software:

  • [FAQ] TDA4VM: What parameters in the VPU driver are used for setting I-frame and IDR key-frame period?

    Part Number: TDA4VM Tool/software: I'm using the TDA4VM Linux or Linux+RTOS 8.6 SDK. What parameters or patches are available to be enable I-frame period and IDR frame period?

  • [FAQ] AM62A7: P-Fail and E-Fail Bad Block Markers

    Part Number: AM62A7 Tool/software: Currently on the AM62A TI EVM, we have a OSPI Serial NAND Flash from Winbond. The flash is: W35N01JWTBAG Let us understand how the BBM is done with respect to some specific registers.

  • [FAQ] AM62x, AM62Px, AM62D-Q1, AM64x, AM275x: Understanding Flash Device ID and Manufacture ID Reads

    Part Number: PROCESSOR-SDK-AM62X Tool/software: In MCU+ SDK, during Flash Initialization, we read the device id and manufacture id. Most common failure is " Unable to read Flash ID... " Let us understand what parameters does the API Flash_norOspiReadID…

View FAQ threads
  • Threads 199049 Discussions