Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: Stream camera of 2 datatypes using 2 Capture nodes and 2 Graphs on the same csi-rx instance

    Part Number: TDA4VM How to Send a YUV input and a raw input from a sensor to the same CSI-RX instance at a time?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP : Custom board hardware design – Processor power-sequencing requirements for power-up and power-down

    Other Parts Discussed in Thread: TPS65220 , AM6442 , SK-AM62B-P1 , AM625 , AM625-Q1 Hi TI Experts, I have the below queries regarding SOC(Processor) power-sequencing requirements for power-up and power-down 1.Is there a recommended power sequence…

  • [FAQ] DP83869-EP: Ethernet compliance Testing failure when interfaced to AM64x

    Part Number: DP83869-EP Other Parts Discussed in Thread: DP83869 Hi Team, I have a customer testing ethernet compliance 1G on the AM64x EVM. They have the same implementation on their custom board and seeing similar failures. There are some failures…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP : Custom board hardware design – Power sequencing between SOC (Processor) and the Attached devices (Fail-safe)

    Other Parts Discussed in Thread: AM625 , AM625-Q1 , AM620-Q1 , AM62A3 , AM62A7 , AM625SIP , AM623 Hi TI Experts, I have the below queries regarding Power supply sequencing between SOC (Processor) and the Attached devices Can I power the SOC (Processor…

  • [FAQ] AM62A3-Q1: Which SPI NAND should use?

    Part Number: AM62A3-Q1 Other Parts Discussed in Thread: AM62A3 Hi Expert, For AM62A3 , Which SPI NAND should use ? OSPI or QSPI ? And what capacity do you suggest ? Is there a maximum or minimum limit on nand capacity? Thanks Daniel

  • [FAQ] SK-AM62: How to configure spidev for MCU_SPI0 CS1 in AM625

    Part Number: SK-AM62 Other Parts Discussed in Thread: AM625 Ref: https://software-dl.ti.com/processor-sdk-linux/esd/AM62X/09_00_00_03/exports/docs/linux/Foundational_Components/Kernel/Kernel_Drivers/SPI.html The default SPI config in Processor SDK…

  • [FAQ] TDA4VM: Getting Shmoo plots for OSPI PHY tuning

    Part Number: TDA4VM Shmoo plots are a useful when it comes to debugging OSPI PHY tuning related issues. This FAQ explains the procedure of getting the shmoo plots from PDK PHY tuning algorithm.

  • [FAQ] AM625SIP Custom board hardware design – Collaterals to Get started

    Part Number: AM625SIP Other Parts Discussed in Thread: AM620-Q1 , AM625 , AM623 , AM625-Q1 , AM62D-Q1 , TPS65219 , SK-AM62-SIP , SK-AM62-LP , SK-AM62B-P1 , AM62L Hi TI Experts, Can you provide a List of collaterals that can be referred when starting…

  • [FAQ] TDA4VM: Integrate Switch Channel functionality in an OpenVX node

    Part Number: TDA4VM How to integrate the switch channel functionality which would select the channel to be processed in an OpenVX node?

  • [FAQ] TDA4VM: Getting started with PDK on windows

    Part Number: TDA4VM Hi, Using PDK with windows requires some pre-setup before you start building the applications. This FAQ explains the setup required for the same.

View FAQ threads
  • Threads 197766 Discussions