Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM62A7 / AM62A7-Q1 / AM62A3 / AM62A3-Q1 / AM62A1 / AM62A1-Q1 and AM62D-Q1 - Custom board hardware design - Schematic Review Checklist

    Part Number: AM62A7-Q1 Other Parts Discussed in Thread: AM62D-Q1 , AM62A7 , AM62A3 , , AM62A3-Q1 Hi Team, Do we have a schematic checklist spreadsheet for customers to fill out for schematic reviews or is the application note on ti.com the full scope…

  • [FAQ] TDA4VM: How do I configure/enable port mirroring in CPSWnG?

    Part Number: TDA4VM How do I configure/enable port mirroring in CPSWnG?

  • [FAQ] AM64X/ AM62X : How to Reset the SOC when WDT timer expires in AM64X and AM62X?

    Part Number: AM6442 Introduction: The primary application of a watchdog timer is as a system monitor to detect and reset an "out of control" SOC. When program execution goes wrong or software or devices are not functioning properly, the watchdog…

  • [FAQ] TDA4VH/AM62A: How to create the CAC mesh LUT for DCC tuning tool input?

    CAC in VPAC3-VISS or VPAC3L-VISS is very similar to LDC in VPAC. To prepare the CAC LUT for DCC tuning tool input, we may use similar matlab/octave script as LDC. You may refer to the LDC FAQ in the link below for more details. e2e.ti.com/.../faq-tda4vm…

  • [FAQ] DRA821: canTxstatus is busy even after Cancellation of Finished messages is set for respective Tx Buffer

    Part Number: TDA4VM Hello, Customer has enabled AUTO retransmission of messages, and Using the CAN channel on TDA4x device to continuously send messages, and then remove other nodes on the CAN bus. Later it entered into Error passive state , and the…

  • [FAQ] PROCESSOR-SDK-J784S4: How Do I Build Yocto Images and Packages for J7 Devices?

    Part Number: PROCESSOR-SDK-J784S4 Other Parts Discussed in Thread: DRA821 , DRA829 , TDA4VM , AM68 , AM69 , SK-AM68 , SK-AM69 How do I build the default yocto images and install new packages for J7 devices?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP : LFOSC usage in the processor

    Part Number: AM625 Other Parts Discussed in Thread: AM62D-Q1 , AM62P-Q1 , , AM62A7-Q1 , AM623 Hi, I have a question from my customer for LFOSC (external 32.668kHz). According to datasheet section 7.11.4.1 Input Clocks / Oscillators, it seems the clock…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62L / AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 / AM62P / AM62P-Q1 Custom board hardware design – EXTINTn pin pullup connection

    Hi TI Experts, I have the below queries regarding the use of EXTINTn pin. Termination recommendations when used. Termination recommendations when not used. Let me know your thoughts.

  • [FAQ] AM62A7 / AM62A7-Q1 / AM62A3 / AM62A3-Q1 / AM62A1-Q1 / AM62D-Q1 Custom board hardware design - FAQs related to Processor collaterals, functioning, peripherals, interface and Starter kit

    Other Parts Discussed in Thread: AM62D-Q1 , SK-AM62A-LP , AM62P , TMUX1308-Q1 , TPS65224-Q1 Hi Board designers, Refer FAQs listed below related to custom board design for AM62Ax and AM62D-Q1 processor families that could be used along with other available…

  • [FAQ] AM625, AM623, AM620-Q1, AM625-Q1, AM625SIP Custom board hardware design - FAQs related to Processor collaterals, functioning, peripherals, interface and Starter kit

    Other Parts Discussed in Thread: AM62D-Q1 , SK-AM62 , SK-AM62B-P1 , SK-AM62-LP , SK-AM62-SIP , SK-AM62B , AM62P , TMUX1308-Q1 , TPS65219 Hi Board designers, Refer FAQs listed below related to custom board design for AM62x processor family that could…

View FAQ threads
  • Threads 197869 Discussions