Answered

• TDA4AP-Q1: Pin Swap for SERDES2_TX2 / RX2 P/N possible via register configuration

  

  Thomas Paula

  Resolved

  Part Number: TDA4AP-Q1 Tool/software: Hello, is it possible to swap the P/N pins for SERDES2_TX2 / SERDES2_RX2 (pins AR21, AR20 / AU20, AU21) by register setting? We're using this port for SGMII/QSGMII SGMII interface 1. Thanks for your answer in advance…

  • Resolved

  • 6 months ago
  • Processors
  • Processors forum

• RE: TAS6584-Q1: THD+N at high temp PBTL

  

  Shadow He

  Hi Tsuji-san What is the condition difference between below two picture? Is it only the temperature difference with 25C and 80C? It seems quite larger than our results. And the low frequency THD also increased a lot, which indicated the noise becomes…

  • 8 months ago
  • Audio
  • Audio forum

• LM4050-N-Q1: Component type for SN29500

  

  Chuqiang Wen

  TI Thinks Resolved

  Part Number: LM4050-N-Q1 Hi Expert, My customer is doing the FuSa analysis for their system. LM4050 is used in this project. Can you help fill the component type to the excel for LM4050 based on SN29500? I saw there have SN29500 category in FuSa FIT…

  • 8 months ago
  • Power management
  • Power management forum

• RE: LM4050-N-Q1: accuracy

  

  Joshua Garcia

  Hi Mingkang, After clarification with back end team the Reverse breakdown voltage change with operating current change (ΔVR/ΔIR) does need to be taken into account in steady state conditions. The reasoning for describing the load regulation…

  • 9 months ago
  • Power management
  • Power management forum

• LM4050-N-Q1: Breakdown voltage temperature coefficient clarification

  

  Scarlett Cao

  TI Thinks Resolved

  Part Number: LM4050-N-Q1 Hi team, Could you pls help share below Ir=1mA is spec at what temperature range? Datasheet has list 25C and full temp range spec for Ir=100uA, but didnt specify it clearly for Ir=10mA/1mA Thank you Scarlett

  • 9 months ago
  • Power management
  • Power management forum
Answered

• TAS6584-Q1: 4Ω BTL Output Power, THD+N Measurement, Test Setup Inquiry. Are All Channels Loaded?

  

  Levi Rakes

  Resolved

  Part Number: TAS6584-Q1 Other Parts Discussed in Thread: TAS6584Q1EVM I have an amplifier project in development right now using the TAS6584QPHDRQ1 amplifier chip. In the output power section of the electrical characteristics table in the datasheet for…

  • Resolved

  • 8 months ago
  • Audio
  • Audio forum

• AMC3336-Q1: Insulation voltage (P/N: AMC3336QDWERQ1)

  

  yasuhiko nudejima

  TI Thinks Resolved

  Part Number: AMC3336-Q1 Hi What is the Insulation voltage between input and output?

  • 10 months ago
  • Data converters
  • Data converters forum
Answered

• LMV358-N-Q1: Looking for CDM value

  

  Akhilesh Dubey

  Resolved

  Part Number: LMV358-N-Q1 Hello, I am looking for CDM value of LMV358-N-Q1, datasheet is not showing the value, I am not sure if TI conducted CDM test for this device or it is just missed to print? Could someone please help on this urgently. Thank you!

  • Resolved

  • 10 months ago
  • Amplifiers
  • Amplifiers forum

• TAS6424E-Q1: The THD+N or THD algorithm

  

  Hsinhung KUO

  TI Thinks Resolved

  Part Number: TAS6424E-Q1 Other Parts Discussed in Thread: TAS6424 Hi TI Team May I ask how to calculate the TAS6424 or TAS6584 for the THD+N or THD algorithm?

  • 10 months ago
  • Audio
  • Audio forum
Answered

• TAS2505-Q1: AP555 THD+N test set up on digital in and analog in

  

  Imelda Zhang

  Resolved

  Part Number: TAS2505-Q1 Other Parts Discussed in Thread: TAS2505 Hi Expert, My customer Bosch is using TAS2505-q1 for quite a long time. We are setting bench to test the THD+N EVM on analog input mode and digital input mode. Analog Input I do the test…

  • Resolved

  • 11 months ago
  • Audio
  • Audio forum

Didn't find what you are looking for? Post a new question.