• 

  Zhanpeng Li

  • 4 months ago
  • Interface
  • Interface forum

  ONET2804T: ONET2804T PCB layout and Bonding Diagram check

  Part Number: ONET2804T Hi team Could you help check the PCB layout and Bonding Diagram? If any potential question remain, could you help identify? I attached the bonding diagram in attachment files. And I attached the PCB layout below: RF side:...
• 

  Naser S.

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: Application

  TI Thinks Resolved

  Part Number: ONET2804T My customer used our TI-TIA ONET2804T in their ROSA, when they test RSSI, they got split in different voltage input, please check the plot: It was tested in Rrssi at 10kohm: (marked red in the second figure), his questions are...
• 

  mick li

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: ONET2804T Design consideration

  TI Thinks Resolved

  Part Number: ONET2804T dear: one of our customer need used ONET2804T on 100G Rosa, have to questions : 1. for the filter capacitor: in the datasheet, It is recommended to use two single layer ceramic (SLC) capacitors in the range of 270 pF to 680...
• 

  Robert Mahar

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: Full Datasheet

  TI Thinks Resolved

  Part Number: ONET2804T I am attempting to get the full datasheet for the ONET2804T TIA. The email address "onet2804t_request@ti.com" bounces back as undeliverable. How can I see the full datasheet and any reference design files? Thanks.
• 

  Robert Mahar

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: Decoupling Capacitors

  TI Thinks Resolved

  Part Number: ONET2804T The datasheet for the ONET2804T recommends 2 single layer caps between 270pF and 680pF to be bonded to the VCCI pads. If the ONET2804T will be mounted direct to the laminate and not to a ceramic substrate, can the VCCI connections...
• 

  Go

  • over 4 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: How to request Full Datasheet

  • Resolved

  Part Number: ONET2804T Hi, I sent a request email about ONET2804T full datasheet
• 

  Thomas Benedett

  • over 3 years ago
  • Amplifiers
  • Amplifiers forum

  ONET2804T: Die Pad pitch and layout

  Part Number: ONET2804T I would like to order one of these parts in die form, but I need to know the pad pitch and pad layout (signal location on the die) on the die so I can design my test board for optimal wirebonding. Can anyone provide me that information...
• 

  Kami Huang60

  • over 1 year ago
  • Interface
  • Interface forum

  RE: ONET1130EC: search for 25Ghz TIA

  Hello Nasser, Thanks for your support. ONET2804T and ONET2804TLP . Best Regards, Kami Huang
• 

  Loren Siebert 1

  • over 4 years ago
  • Interface
  • Interface forum

  RE: ONET2804T Suitable for APD & PIN photodiodes

  Hello Steve, The ONET2804T was designed specifically to interface with a PIN diode with a 2.5V reverse bias voltage. The "Filter" pins self bias to this voltage and the pad spacing on the ONET die match with the pad spacing on several PIN...
• 

  Loren Siebert 1

  • over 2 years ago
  • Amplifiers
  • Amplifiers forum

  RE: ONET8551T: Bond Pad Material

  Hi Jacob, Quince, I have confirmed that the bond pads are aluminum. I don't have an answer for the passivation yet. I would guess silicon dioxide, but I am not sure. Page 24 of the ONET2804T datasheet has some guidance on bond wire configuration...

Didn't find what you are looking for? Post a new question.

• Ask a new question