Search tips
Showing 32 results View by: Thread Post Sort by

  • How to use THS3095 EVM

    Other Parts Discussed in Thread: THS3095 How to use THS3095 EVM to test its second harmonics distortion and compare to its datasheet specification? Current design configuration: Non-inverting amp Rf = 1.96k ohm, Rg = 68.1 ohm (Gain ~25dB) Input: 23.49MHz…

  • RE: TIDA-01486: Difference in Simulation Results and Hardware Values

    Hi, The model of the THS3095 you have in there is an older revision, where the polarity of the PD pin is the other way round. Either use the new model from the product page, or simply tie PD to GND should solve your problem. Bets regards, Steffen
    • Answered

  • power-down with THS3095

    Resolved
    Other Parts Discussed in Thread: THS3095 Hello, I have problems with power down of THS3095. Regardless of level of voltage at pin 8 (nPD) - the device is always enabled (indicated by power consumption, voltage levels and amplifying function). At first…
    • Resolved
    • Answered

  • THS3095 is overheating

    Resolved
    Other Parts Discussed in Thread: THS3095 Hi, i am using THS3095 as shown on a picture below Both outputs is OK, but all amplifiers becoming extremely hot in a few minutes after power up, even without input signals (inputs are grounded). Output loads are…
    • Resolved

  • TIDA-01486: Overheating design - need clarification

    TI Thinks Resolved
    Part Number: TIDA-01486 Other Parts Discussed in Thread: THS3095 Hi, My customer just received their newly built TIDA-01486 AFE board and smelled 'hot components'. When large signals pass the RX portion, the 10ohm resistors R39-R42 may source…

  • TIDA-01486: TIDA-01486 for amplification of driving power

    TI Thinks Resolved
    Part Number: TIDA-01486 Other Parts Discussed in Thread: EVM430-FR6047 , , MSP430FR6047 , TS5A3357 , THS3095 Hello, I use the EVM430-FR6047 for ultrasonic volume flow measurement and the TIDA-01486 reference design. After connecting the TIDA-01486 to the EVM430…
    • Answered

  • MSP430FR6047: is this allowed?

    Resolved
    Part Number: MSP430FR6047 Other Parts Discussed in Thread: THS3095 , EVM430-FR6043 Hi, in the watersample, specificallly "FR6047_USSWLib_template_example" which I used to start from, in the file: ussSWLib/source/ussSwLibMeasurement.c line 518…
    • Resolved

  • MSP430FR6047: External Amplification and External / Internal DC-Bias Conflict

    TI Thinks Resolved
    Part Number: MSP430FR6047 Other Parts Discussed in Thread: TIDA-01486 , THS3095 I have recently designed a "UltraSonic Flow Meter" based around the MSP430FR6047 that uses external switches and amplification circuitry, almost identical to the …

  • THS3491: Spice model Compatible with Multisim?

    TI Thinks Resolved
    Part Number: THS3491 Other Parts Discussed in Thread: THS3091 , THS3095 , TINA-TI Hello, Is it possible to simulate this component in NI Multisim? Multisim has the THS3091 and THS3095 components in its library, but it does not have the THS3491. I tried to…

  • Switching a 0-28V pulse in less than 10ns

    Other Parts Discussed in Thread: THS3491 , TINA-TI , THS3062 , THS3095 , LM7171 , BUF634A Hello, In my project I would like to switch the output of 0-28V pulse in less than 10ns. The rise and fall times should be less than 10ns. A XILINX FPGA shall drive the…

Didn't find what you are looking for? Post a new question.