Frequent Questions

  • [FAQ] Which TI devices support the HART protocol?

    Part Number: AFE881H1 Other Parts Discussed in Thread: DAC161S997 , DAC161P997 , DAC8750 , DAC7750 , DAC8760 , DAC7760 , DAC8771 , DAC8775 , DAC8740H , DAC8741H , DAC8742H , , AFE781H1 , AFE882H1 , AFE782H1 Tool/software: Which TI devices support…

  • [FAQ] MCU-PLUS-SDK-AM261X: How to Configure MII mode in AM261x MCU_PLUS_SDK

    Part Number: MCU-PLUS-SDK-AM261X Other Parts Discussed in Thread: DP83826-EVM-AM2 , SYSCONFIG Tool/software: Hi Experts, I am using AM261x-LP with MCU_PLUS_SDK for AM261x v10.00.01.10. For CPSW Based networking examples, I am unable to configure MII…

  • [FAQ] DP83TC812S-Q1: RGMII Shift and Align Mode

    Part Number: DP83TC812S-Q1 Tool/software: Hello, Here is a summary of available information about RGMII Shift and Align mode for our DP83TC81x devices: A minimum of 1ns setup and 1ns hold time must be maintained at the input of the receiver…

  • [FAQ] LMH1239: SDI Layout Suggestions

    Part Number: LMH1239 Other Parts Discussed in Thread: LMH1297 Tool/software: Hello SDI engineers and LMH enthusiasts, Figure 1 - 3:5 for SDI In this E2E FAQ, I will be discussing GND plane layout best practices for SDI designs. In cable driver…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62Px / AM62D-Q1 / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design - Queries related to IBIS model

    Part Number: AM625 Other Parts Discussed in Thread: AM6442 , DS160PR810 , AM67 Tool/software: Hi TI Experts, Do you have recommendations on using the IBIS model?

  • [FAQ] AM62x & AM64x: How to enable PRU RPMsg on Processor SDK Linux 11.0

    Part Number: PROCESSOR-SDK-AM62X In Linux kernel 6.12, we remove the separate PRU RPMsg (RPMessage) driver, and use the generic RPMsg driver instead. However, the changes were not complete in time for Linux SDK 11.0. This means that PRU RPMsg does not…

  • [FAQ] PROCESSOR-SDK: Getting Started with GPIOs in Linux using the AM62 and AM64 Family Processors

    Part Number: PROCESSOR-SDK-AM62X Other Parts Discussed in Thread: AM62P , AM62L , SK-AM64B , SK-AM62B-P1 , SK-AM62-LP , SK-AM62A-LP , SK-AM62P-LP , TMDS62LEVM , AUDIO-AM62D-EVM , SYSCONFIG Tool/software: The objective of this FAQ is for someone with…

  • [FAQ] TDA4VM: How to enable MCU R5F cores running in split mode in SPL boot flow.

    Part Number: TDA4VM Tool/software: TI SDKs by default configures MCU R5F running in lock step mode, how to configure to run MCU R5F in Split Mode.

  • [FAQ] AM2612: Device 'Cortex R.AM261x' is not currently recognized: CCS is not detecting AM261x

    Part Number: AM2612 Tool/software: Hi TI experts, I am using CCS v12.8.1, MCU_PLUS_SDK for AM261x. If I try to import any example from AM261x MCU+ SDK, I get the following error: Even if I try to create a new Project from scratch, it says " Device…

  • [FAQ] MCU-PLUS-SDK-AM261X: All ADC2 outputs are '0' on AM261x devices

    Part Number: MCU-PLUS-SDK-AM261X Other Parts Discussed in Thread: LP-AM261 , SYSCONFIG Tool/software: Hi TI experts, All ADC2 values output as '0' on AM261x. Example output on is adc_multiple_soc_epwm_am261x-lp_r5fss0-0_nortos_ti-arm-clang and on…

View FAQ threads
Recommended For You