Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How to build, flash and boot Linux from GPMC-NAND on AM64x

    Part Number: AM6442 Other Parts Discussed in Thread: TMDS64EVM The FAQ lists steps on how to build, flash, and boot linux from GPMC-NAND on TMDS64EVM [1] and [2] with AM64x Linux SDK 12.1.0.5.3 [3] + the attached u-boot and kernel patches. [1]. TMDS64EVM…

  • [FAQ] DDR part selection guidance for Sitara Processors

    Other Parts Discussed in Thread: AM62P , AUDIO-AM62D-EVM , AM62L , AM67 , AM67A Table of Contents Introduction How to Select a Compatible DDR Device Step-by-Step Design Guide Validation Guidance DDR Margin Tool Frequently Asked Questions…

  • [FAQ] SYSFW symmetric keyring import and applications on AM64x

    Part Number: AM6442 SYSFW/TIFS adds the new feature on symmetric keyring import in TIFS 12.0.2 release https://software-dl.ti.com/tisci/esd/latest/6_topic_user_guides/keyring.html https://software-dl.ti.com/tisci/esd/latest/2_tisci_msgs/security/keyring…

  • [FAQ] TDA4VM-Q1: How to configure MCAN hardware message ID filters on A72 Linux

    Part Number: TDA4VM-Q1 Other Parts Discussed in Thread: AM68 , TDA4VM , AM69 , TDA4VH , AM67 How can I configure MCAN hardware message ID acceptance filters from Linux (A72) so that the CAN controller discards unwanted IDs before they reach the socket…

  • [FAQ] TDA4AEN-Q1: Steps to Load and Execute a Standalone Binary on J722S EVM via CCS

    Part Number: TDA4AEN-Q1 Other Parts Discussed in Thread: AM67 Hi Team, What are the steps required to load, run, and debug a standalone application on a J722S EVM using Code Composer Studio (CCS), including hardware setup, target connection, executable…

  • [FAQ] TDA4AEN-Q1: How to set up the C7x LUT (C7100/C7120) and ILUT (C7524), with examples and build steps

    Part Number: TDA4AEN-Q1 Other Parts Discussed in Thread: AM67A , SYSCONFIG How do I configure and use the C7x DSP LUT (C7100/C7120) and the ILUT (C7524), including example code, how to build it on the target, and how to measure performance?

  • [FAQ] TDA4VH-Q1,TDA4VE,TDAVAL,TDA4VL,TDA4VP-Q1,TDA4AP-Q1: How to Enable Temperature driven Dynamic Refresh rate adjustment?

    Part Number: DRA821U-Q1 How to Enable Temperature driven Dynamic Refresh rate adjustment for DDR?

  • [FAQ] AM62A7: DCC, SDL Clock Configuration

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG , AM62A3-Q1 How to configure clock source for DCC Safety Diagnostic ?

  • [FAQ] DRA821U-Q1: USXGMII +PCIE SUPPORT ON MAIN CPSW5G: J7200 EVM

    Part Number: DRA821U-Q1 How to enable USXGMII + PCIE on MAIN CPSW5G in J7200 EVM ?

  • [FAQ] AM2754-Q1: AUDIO-AM275-EVM: McASP4 signals not appearing on J28 connector

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: AUDIO-AM275-EVM , TXB0108 , TCA6416 I am trying to use McASP4 pins on the J28 User Expansion Connector on the AUDIO-AM275-EVM board. I have configured the syscfg for McASP4 and built my firmware…

View FAQ threads
  • Threads 203860 Discussions