• Threads 51721 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] MSPM0G3519: Advanced Timer Techniques in MSPM0 (application note - sdaa286)

    Part Number: MSPM0G3519 This E2E thread contains reference application codes for the Application Note titled- Advanced Timer Techniques in MSPM0. Advanced Timer (TIMA) peripherals in MSPM0 Devices are designed to meet the demands of modern embedded…

  • [FAQ] AM2634: Sending Large Amounts of Data from an AM263x SPI Slave with Minimal CS Deassertion Time

    Part Number: AM2634 Other Parts Discussed in Thread: SYSCONFIG In this FAQ, I explain an approach to transmit a large amount of data from an AM263x SPI slave device while keeping the chip select (CS) deassertion time to a minimum.

  • [FAQ] AM263P4: I2C OWN TArget Address

    Part Number: AM263P4 Other Parts Discussed in Thread: SYSCONFIG What is the meaning of I2C Own Target address in the syscfg file below. Is this related to the I2C controller or the I2C transmitter? What are the valid values it can take?

  • [FAQ] AM2634-Q1: How to enable LWIP host name in AM263

    Part Number: AM2634-Q1 LWIP enabled devices can get IP address from DHCP server based on host name. To enable this feature on LWIP stack, certain configuration needs to be done. - Let us pick the enet_cpsw_tcpserver example to enable this feature…

  • [FAQ] AM263P4: How to block ethernet packets with a particular unicast address?

    Part Number: AM263P4 Ethernet packets can be blocked or forwarded based on their packet addresses. Unicast address is a specific type of address that is intended for one to one communication. ALE in CPSW susbystem can be configured to drop packets…

  • [FAQ] AM2634-Q1: How can I persist a data structure from my code in flash storage on an AM263 microcontroller?

    Part Number: AM2634-Q1 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH This FAQ highlights how you make a datastructure to be stored in flash in AM263 microcontroller. Typically we can do this in AM263Px and AM261x microcontroller where XIP…

  • [FAQ] AM263P4-Q1: How to flash/program custom external flashes

    Part Number: AM263P4-Q1 Other Parts Discussed in Thread: UNIFLASH This FAQ explains how to setup the flash utility to flash into external flashes which are not supported out of the box. The method mentioned in this FAQ would be the same for AM261 and…

  • [FAQ] MSPM0-SDK: Software and Evaluation Board Design Resources for Application note of Single Phase AC Shunt Power Monitor with Low Cost MSPM0

    Part Number: MSPM0-SDK This thread is used to update the software or hardware update for application note of Single Phase AC Power Monitor with MSPM0 Hardware_Software.zip

  • [FAQ] printf demo for MSPM0 device

    Other Parts Discussed in Thread: LP-MSPM0G3507 printf_to_uart_LP_MSPM0G3507_nortos_ticlang.zip Default UART pin is PA10 and PA11, and it's based on LP-MSPM0G3507 default. Please check corresponding Launchpad's User guide schematic before test. There…

  • [FAQ] AM2612-Q1: How to debug XIP application using CCS Theia

    Part Number: AM2612-Q1 Hi Experts, Please share the steps to debug XIP applications using CCS Theia.

View FAQ threads