TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel
Motor drivers

Motor drivers

Motor drivers forum

  • Mentions
  • Tags
  • More
  • Cancel
  • Ask a new question
  • Ask a new question
  • Cancel
Texas Instruments (TI) Motor drivers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search motor drivers IC content or ask technical support questions on everything from brushless DC (BLDC) and brushed DC (BDC) motor drivers to stepper motor and other drivers for precise motor control. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions
  • [FAQ] Selecting the Best IDRIVE setting and Why this is Essential

    Adam Sidelsky
    Adam Sidelsky
    Using the wrong IDRIVE setting can damage your FET or DRV as it often causes excessive ringing and/or cross-conduction when the Gates are slammed on or off too strongly. This document discusses the methods and some Do's and Don'ts IDRIVE Do's and Don…
    • over 6 years ago
    • Motor drivers
    • Motor drivers forum
  • [FAQ] Best Practices for PCB layout of Motor Drives

    James Lockridge19
    James Lockridge19
    "What are good layout practices for your motor driver IC?" This is a question frequently asked to TI's motor driver team. Poor layout can result in poor EMI performance, poor thermal performance, or sometimes the motor driver device just doesn't work…
    • over 6 years ago
    • Motor drivers
    • Motor drivers forum
<

View FAQ threads
  • Tags
  • RSS
  • More
  • Cancel
  • Suggested Answer

    DRV8316: abnormal situation 0 Locked

    209 views
    1 reply
    Latest over 2 years ago
    by Akshay Rajeev Menon
  • Answered

    DRV8305: Gate timing interpretation 0 Locked

    268 views
    1 reply
    Latest over 2 years ago
    by Akshay Rajeev Menon
  • Suggested Answer

    MCT8329A: Does the MCT8329A have a mode that does not allow writing to EEPROM or RAM? 0 Locked

    201 views
    1 reply
    Latest over 2 years ago
    by Joshua Horlander Cruz
  • Not Answered

    DRV8301: GVDD Pin Undervoltage: Voltage Ranges and Troubleshooting 0 Locked

    559 views
    8 replies
    Latest over 2 years ago
    by Joshua Maize
  • Suggested Answer

    DRV8312: PVDD: Absolute max ratings vs Recommended Operating Conditions 0 Locked

    249 views
    3 replies
    Latest over 2 years ago
    by Joshua Maize
  • Not Answered

    MCT8329A: Cannot be written to MCT8329A EEPROM. 0 Locked

    301 views
    5 replies
    Latest over 2 years ago
    by Conor
  • Answered

    MCF8316A: Torque control mode 0 Locked

    727 views
    14 replies
    Latest over 2 years ago
    by joe van Niekerk
  • Suggested Answer

    DRV8300DIPW-EVM: 3d step model 0 Locked

    156 views
    1 reply
    Latest over 2 years ago
    by Akshay Rajeev Menon
  • Discussion

    Input Power increase when increased the potential divider resistor. Locked

    227 views
    7 replies
    Latest over 2 years ago
    by LeonardEllis
  • Not Answered

    DRV8825: Why does the fault pin read 0.25 V? That is logic low, yet the motors still move. 0 Locked

    1073 views
    9 replies
    Latest over 2 years ago
    by Jacob Thompson
  • Not Answered

    DRV8874: PMODE voltage level is not stable 0 Locked

    278 views
    3 replies
    Latest over 2 years ago
    by Jacob Thompson
  • Suggested Answer

    DRV110EVM: DRV110 Frequency PWM 0 Locked

    310 views
    3 replies
    Latest over 2 years ago
    by David Medis
  • Suggested Answer

    DRV8818: firmware implementation for current sensing with external shunt 0 Locked

    252 views
    2 replies
    Latest over 2 years ago
    by Ryan Kehr
  • Answered

    DRV110EVM: R3 value 0 Locked

    424 views
    7 replies
    Latest over 2 years ago
    by Jacob Thompson
  • Not Answered

    DRV10983: Insufficient drive voltage 0 Locked

    301 views
    7 replies
    Latest over 2 years ago
    by Vishnu Balaraj
  • Suggested Answer

    DRV8243-Q1: VDD during sleep state 0 Locked

    265 views
    1 reply
    Latest over 2 years ago
    by Ryan Kehr
  • Not Answered

    DRV8311: The output voltage of nFAULT pin issue 0 Locked

    410 views
    3 replies
    Latest over 2 years ago
    by Joshua Maize
  • Answered

    DRV8316: DRV8316 Open loop Current waveform 0 Locked

    427 views
    2 replies
    Latest over 2 years ago
    by Joshua Maize
  • Suggested Answer

    DRV8316: DRV8316 related issues 0 Locked

    251 views
    2 replies
    Latest over 2 years ago
    by Joshua Maize
  • Answered

    DRV110: Hold current Calculation 0 Locked

    230 views
    1 reply
    Latest over 2 years ago
    by David Medis
<>