Texas Instruments (TI) Power management support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search power management IC content or ask technical support questions on everything from linear and DC/DC switching regulators to battery management and LED drivers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TPS53353: PGOOD pin connected to an external voltage source and/or MCU/FPGA monitor effects on the MODE settings

    Part Number: TPS53353 Other Parts Discussed in Thread: TPS53355 With PGOOD pulled up externally to an MCU or FPGA and an external voltage source, I would not expect any issues in the soft-start/mode selection so long as the probe monitoring PGOOD is…

  • [FAQ] How to add DESAT or short circuit protection to gate drivers

    Part Number: UCC21530-Q1 Other Parts Discussed in Thread: UCC21759-Q1 , UCC21750 , UCC21739-Q1 , UCC21732-Q1 , ISO5851 , ISO5851-Q1 , ISO5852S-EP , ISO5852S-Q1 , UCC21710 , ISO5852S , UCC21710-Q1 , UCC21732 , UCC21736-Q1 , UCC21750-Q1 , UCC5390 , UCC21520…

  • [FAQ] End of life (applies to ALL TI devices)

    Other Parts Discussed in Thread: LMG1210 Hi, I want to use the LMG1210 for a new design, but I want to make sure that I can manufacture the part for a few years to come. My question is when was the LMG1210 released and when will it reach it's end-of…

  • [FAQ] TPS54824: What is the startup process in terms of FB, SS/TRK and COMP pins?

    Part Number: TPS54824 The device has been designed to prevent the low-side MOSFET from discharging a pre-biased output. During monotonic pre-biased startup, the low-side MOSFET is not allowed to sink current until the SS/TRK pin voltage is higher than…

  • [FAQ] TPS54A24: How to reduce noise at Vin, Vout and when taking measurements?

    Part Number: TPS54A24 Noise reduction for VIN and VOUT There are things which can be done to reduce this noise such as adding a boot resistor or snubber, adding input or output caps for high frequency bypass or adding some inductive filtering. Noise…

  • [FAQ] LM5141: loop compensation

    Part Number: LM5141 Hi there, about LM5141 test, I have some questions. 1. Equation(60) shows calculating Rcomp, how this equation comes from? any more detialed deduction? 2.when inductor is too large, loop instability occurs. You said it's because…

  • [FAQ] BQ25890: Why ADC monitoring sometimes does not work when battery only for BQ25890, BQ25890H, BQ25892, BQ25895, BQ25895M, BQ25896, BQ25898, BQ25898D, BQ25898C?

    Part Number: BQ25890 Other Parts Discussed in Thread: BQ25898 , BQ25896 , BQ25895 , BQ25898D , BQ25898C , BQ25892 , , , BQ25895M Hi, When only the battery is present, ADC monitoring works only when the battery voltage is above the MINSYS register…

  • [FAQ] How to terminate or set the termination current of the buck-boost charger controller for BQ25710, BQ25720, BQ25730 etc.?

    Other Parts Discussed in Thread: BQ25720 , BQ25730 , BQ25710 , BQ25703A , BQ25713 , BQ25731 , BQ25700A , BQ25708 , BQ25723 , BQ25713B How to terminate or set the termination current of the buck-boost chargers?

  • [FAQ] Which buck-boost charge controller should I select for my charging application in BQ25700x, BQ25710, BQ25720 and BQ25730 families?

    Which buck-boost charge controller should I select for my charging application?

  • [FAQ] How do I ensure the charger layout is satisfactory? Is there a guideline for the buck-boost charger controllers like BQ25713, BQ25720 and BQ25730 etc.?

    Other Parts Discussed in Thread: BQ25720 , BQ25713 , BQ25730 , BQ25703A , BQ25731 , BQ25710 , BQ25700A , BQ25708 , BQ25723 , BQ25713B How do I ensure the charger layout is satisfactory? Is there a guideline for the buck-boost charger controllers like…

View FAQ threads