Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] : How to trigger DMA with the help of GPIO on AM64X/AM243 and AM62X devices ?

    Part Number: AM6412 Tool/software: Hello Users, Many users are asking to trigger DMA with the help of GPIO on AM64X/AM243 and AM62X devices. So, I have created an example of this solution on AM64X and the procedure is the same for all other devices…

  • [FAQ] PROCESSOR-SDK-AM64X: How to create a PWM using a timer

    Part Number: PROCESSOR-SDK-AM64X Tool/software: Hi, can we use a timer to generate a PWM? If so, how could we control/change its frequency and duty cycle while running?

  • [FAQ] AM623: Power-Up Sequencing for VPP?

    Part Number: AM623 Tool/software: Hi Expert, Power-Up Sequencing refers to the datasheet to set up, but now I have a question about the power-up timing of the VPP voltage. And the Figure 7-5. Power-Up Sequencing graphic shows Hi-Z. I don’t quite…

  • [FAQ] AM64x/AM243 : How to enable SYSFW trace on AM64x/AM243 devices

    Part Number: AM6412 Tool/software: In AM64x/AM243 devices, we are using DMSC core (M3 core) for doing Resets, individual core Reset, SOC Reset, Core or IP frequency settings and resource allocation and security operations . We need to use SCI client…

  • [FAQ] TDA4VH-Q1: Achieving Functional Safety with Boot

    Part Number: TDA4VH-Q1 Tool/software: Provide the steps to integrate SDL functional safety modules such as BIST, POK, VTM and TOG with the PDK Boot Application.

  • [FAQ] AM62A3: CPSW3G RGMII phy-less interface to external switch

    Part Number: AM62A3 Tool/software: Hi, a customer is using the AM62A and connects to an external ethernet switch with the RGMII interface. We are looking at the appnote https://www.ti.com/lit/an/sprad07/sprad07.pdf The design currently does…

  • [FAQ] AM625: What's the purpose for the pull down R on MMC_CLK?

    Part Number: AM625 Tool/software: Dear Sir, May I know what the purpose for the pull down R on MMC_CLK signal on TI EVM?

  • [FAQ] TDA4VM: How do we avoid UDMA resource conflict issues when integrating the MCAL Eth module with other modules?

    Part Number: TDA4VM Other Parts Discussed in Thread: SYSCONFIG Tool/software: How do we avoid UDMA resource conflict issues when integrating the MCAL Eth module with other modules?

  • [FAQ] TDA4VH: How do we enable all eight(8) external ports of CPSW9G in TDA4VH using TI EVM?

    Part Number: TDA4VH Tool/software: How do we enable all eight(8) external ports of CPSW9G in TDA4VH using TI EVM?

  • [FAQ] TDA4VM: How do I resolve these compilation errors when building PDK examples?

    Part Number: TDA4VM Tool/software: I am trying to resolve the following errors when attempting to build examples within the RTOS PDK. How can I resolve these errors? SDK: 9.0+ Error Log 1: ti/ti-processor-sdk-rtos-j721e-evm-09_02_00_05/pdk_jacinto_09_02_00_30…

View FAQ threads
  • Threads 198382 Discussions