Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM6442: 1Gbps ethernet phy which can support both copper and OFC cables

    Part Number: AM6442 Other Parts Discussed in Thread: DP83869 Hi Team , we are developing a hardware based on AM6442ASFGGAALV. We have following initial queries .Please help We need a 1Gbps ethernet phy which can support both copper and OFC cables…

  • [FAQ] SK-AM68: How do I run the core-image-weston on SK-AM68?

    Part Number: SK-AM68 I want a minimal configuration to run graphics applications using Weston since the full SDK image is not necessary for the development of my application. Currently, when I try to boot the core-image-weston as is from the Yocto build…

  • [FAQ] How do I disable the GPU driver from loading?

    I need to disable the GPU driver from automatically loading when I boot Linux, how can I disable the auto-loading of the driver?

  • [FAQ] How to flash and boot u-boot from serial-NAND on AM62x/AM62Ax

    Other Parts Discussed in Thread: SK-AM62 , SK-AM62-LP , SK-AM62A-LP AM62x/AM62Ax Boot ROM supports booting from (x)SPI-NOR and Serial-NAND. Please refer to AM62x/AM62Ax TRM "Chapter 5 Initialization" for details. The OSPI-NOR and OSPI-NAND are installed…

  • [FAQ] AM62A7 / AM62A7-Q1 / AM62A3 / AM62A3-Q1 / AM62A1-Q1 and AM62D-Q1: Internal pull configuration registers for MCU_I2C0 and WKUP_I2C0

    Part Number: AM62A7-Q1 Other Parts Discussed in Thread: AM62P Hello Experts, In the TRM, there is following description >These bits do not apply to "I2C OD FS" buffer types as these IOs do not have internal pull registers. >The MCU_I2C0 and WKUP_I2C0…

  • [FAQ] AM64x, AM243x (ALV, ALX), AM62x, AM62Ax, AM62Px, AM62D-Q1, AM62L Custom board hardware design - Collaterals for Reference during Schematic Design and Schematics Review

    Other Parts Discussed in Thread: AM6442 , AM6411 , AM6422 , AM6412 , AM6421 , AM6441 , AM2434 , AM2432 , AM2431 , AM625 , AM623 , AM625-Q1 , AM620-Q1 , AM625SIP , AM62L , AM62A7 , AM62A3 , AM62A1-Q1 , AM62A7-Q1 , AM62D-Q1 , AM62P , AM62P-Q1 Hi TI Experts…

  • [FAQ] AM3352: LCD display may flicker by using LCD controller

    Part Number: AM3352 Other Parts Discussed in Thread: DS92LV2412 , DS92LV2411 , Hi, The AM3352 and LCD are not directly connected, but are configured as AM3352 → LCD serialiser(DS92LV2411) → LCD deserialiser(DS92LV2412) → LCD. The flickering frequency…

  • [FAQ] AM62A7 / AM62A7-Q1 / AM62A3 / AM62A3-Q1 / AM62A1 / AM62A1-Q1 and AM62D-Q1 - Custom board hardware design - Schematic Review Checklist

    Part Number: AM62A7-Q1 Other Parts Discussed in Thread: AM62D-Q1 , AM62A7 , AM62A3 , , AM62A3-Q1 Hi Team, Do we have a schematic checklist spreadsheet for customers to fill out for schematic reviews or is the application note on ti.com the full scope…

  • [FAQ] TDA4VM: How do I configure/enable port mirroring in CPSWnG?

    Part Number: TDA4VM How do I configure/enable port mirroring in CPSWnG?

  • [FAQ] AM64X/ AM62X : How to Reset the SOC when WDT timer expires in AM64X and AM62X?

    Part Number: AM6442 Introduction: The primary application of a watchdog timer is as a system monitor to detect and reset an "out of control" SOC. When program execution goes wrong or software or devices are not functioning properly, the watchdog…

View FAQ threads
  • Threads 198113 Discussions