Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: Custom board hardware design - SD card (MMC1) VDD power supply

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62-LP Tool/software: Hi, My customer is using SD card boot only for development phase. For production, only QSPI boot is used. QSPI or SD card boot selection is done by DIP switch on the board…

  • [FAQ] AM644x: Pin Attributes in excel

    Part Number: AM62A7-Q1 Other Parts Discussed in Thread: AM6442 Tool/software: Can you supply the pin list of the AM6442 in excel format? Thanks

  • [FAQ] AM62A7: How to stream video from AM62x devices over Wi-Fi using CC33XX

    Part Number: AM62A7 Other Parts Discussed in Thread: CC3301 , AM62P , AM625 , AM620-Q1 , AM625-Q1 , AM62P-Q1 , AM62A3 , , AM67A , CC3351 , CC3350 , AM623 , CC3300 , SK-AM62B , SK-AM62A-LP , SK-AM62P-LP , BEAGLEY-AI , M2-CC3351 Tool/software: I saw…

  • [FAQ] AM62A7: Bad Block Implementation for NAND Flash Parts

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG Tool/software: From release 10.00.00.14 onwards, BBM has been implemented in TI Drivers for NAND Flash Parts. AM62A MCU SDK: https://www.ti.com/tool/download/MCU-PLUS-SDK-AM62A/10.00…

  • [FAQ] TPS62867: TPS62867RQYR head room

    Part Number: TPS62867 Tool/software: Hi Experts, Customer is using the below device The input is 3.6V - 5% The output is 3.3V + 5% Current 1-2 A. Is there a min voltage difference that is required between the output and the input. Regards…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62D-Q1 / AM62Px / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design – SOC ROC Recommended Operating Condition

    Part Number: AM625 Tool/software: HI TI experts, I have a question on the SOC ROC. Can i consider the ROC to be ±5% of the Nominal value for the supply rails or should i be considering the values mentioned in the data sheet ( some of the supplies…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62Ax / AM62D-Q1 / AM62Px / AM64x / AM243x Design Recommendations / Custom board hardware design – Queries related to CAP_VDDSx CAP_VDDS

    Part Number: AM625 Other Parts Discussed in Thread: AM62L Tool/software: HI TI experts, Could you provide recommendations on CAP_VDDSx, cap value and effect of the capacitor not mounted or shorted.

  • [FAQ] PROCESSOR-SDK-AM57X: U-boot patch for Linux addressing AM57xx errata i2446

    Part Number: PROCESSOR-SDK-AM57X Tool/software: This is a patch to made for U-boot as an example of how to implement the workaround for AM57xx errata i2446:

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: Ethernet PHY RGMII synchronous clock

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62B-P1 Tool/software: Hello, May I have question about SoC clock? Q1 In this document, https://www.ti.com/lit/an/sprad21e/sprad21e.pdf It says EPHY need match clock to SoC. Is the…

  • [FAQ] SK-AM64B: Why the Ethernet phy use the same clock buffer?

    Part Number: SK-AM64B Tool/software: Hi Team, I found in the schematic of EVM, we only use one piece of LMK1C1103PWR to buffer clock signal to 2 pieces of Ethernet PHY. Does it necessary to use one clock buffer? Can the different Ethernet PHY use…

View FAQ threads
  • Threads 198177 Discussions