Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: How to change eDP driver for the different sysclk0 input?

    Part Number: TDA4VM eDP driver has dependency on the reference clock input. Many of the eDP parameters are calculated/configured based on the reference clock input.. These parameters include receiver detect, output lane speed, clock oscillator parameters…

  • [FAQ] TDA4VM: K3 ResPart Tool fails to open on SDK 8.5

    Part Number: TDA4VM Other Parts Discussed in Thread: SYSCONFIG , TDA4VL , DRA821 , I am trying to use the K3 Resource Partitioning Tool plugin with SysConfig. I followed the steps in the Getting Started section of the K3 Resource Partitioning Tool, but…

  • [FAQ] EVMK2G: How to run GPIO Examples for DSP core on K2G EVM

    Part Number: EVMK2G How to do build, run and test the K2G GPIO example projects in the DSP core from TI-RTOS SDK?

  • [FAQ] AM623 Custom board hardware design – Collaterals to Get started

    Part Number: AM623 Other Parts Discussed in Thread: AM620-Q1 , AM625 , , AM625-Q1 , AM625SIP , AM62D-Q1 , TPS65219 , SK-AM62B-P1 , SK-AM62-LP , SK-AM62B , SYSCONFIG , SK-AM62 Hi TI Experts, Can you provide a List of collaterals that can be referred…

  • [FAQ] AM6442( AM64X) : How to Toggle GPIO Pin on PRU?

    Part Number: AM6442 Other Parts Discussed in Thread: SYSCONFIG Sitara devices have PRU cores that can execute instructions in a fully deterministic manner. Therefore, users can use PRU cores for real-time I/O control applications. This FAQ is intended…

  • [FAQ] AM625 Custom board hardware design – Collaterals to Get started

    Part Number: AM625 Other Parts Discussed in Thread: AM620-Q1 , , AM623 , , , AM62D-Q1 , TPS65219 , SK-AM62B-P1 , SK-AM62-LP , SK-AM62B , SK-AM62 , SYSCONFIG Hi TI Experts, Can you provide a List of collaterals that can be referred when starting a…

  • [FAQ] AM64X: How to Load/Flash PRU binaries into external memory

    Part Number: AM6442 Other Parts Discussed in Thread: UNIFLASH How can I load/flash PRU binaries into external memory? I want to keep my PRU software in external memory and for every time reset the AM64X SOC, it has to read PRU binaries from external…

  • [FAQ] AM64X: How can I flash SOC initialization binaries on HS - FS HW versions .

    Part Number: AM6442 Other Parts Discussed in Thread: UNIFLASH Note: This Procedure is used only for MCU+SDK RTOS/No-RTOS OS , Not for Linux OS If you are trying to send prebuilt sbl_uart_uniflash.release.tiimage and sbl_null.release.tiimage images…

  • [FAQ] TDA4VM: CPSW9G Ethernet switch not working out-of-the box SDK 8.5 onwards

    Part Number: TDA4VM Other Parts Discussed in Thread: TDA4VH , DRA821 , DRA829 I created an SD card using the mksdboot.sh script in the [PSDK-LINUX-INSTALL-DIR]/bin in PSDK Linux 8.5. I do not see any interfaces corresponding to CPSW9G ethernet controller…

  • [FAQ] AM623: MCU_OSC0 transconductance parameter

    Part Number: AM623 Asking on behalf of a customer: Regarding the MCU_OSC0 Internal Oscillator circuit, could you provide the trans-conductance (gm_critical) of it. We could not find the information in the datasheet. We are in contact with [Crystal…

View FAQ threads
  • Threads 198456 Discussions