Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 Custom board hardware design – Processor DDR Subsystem and Device Register configuration

    Other Parts Discussed in Thread: AM62P , AM625 , AM623 , AM625-Q1 , AM62P-Q1 , SYSCONFIG Hi TI Experts, Could you explain the configurations that are required to be done for the below use cases? Device used in the EVM is used. A new functionally…

  • [FAQ] TDA4VM: How to print the ALE table for CPSW in TDA4/DRA8 devices

    Part Number: TDA4VM Other Parts Discussed in Thread: DRA821 , , TDA4VH , DRA829 Are there any tools available for printing ALE for the different ethernet applications with enet LLD, ethfw and Native Linux Driver?

  • [FAQ] A53 boot binary (tispl.bin) loading error when BOOTMODE[7]="0" in eMMC boot mode on AM62x

    AM62x boot-rom support on booting R5-SPL/SBL from eMMC is described in Chapter 5 Initialization of AM62x TRM It is summarized in the table below. Note that booting from eMMC boot partition with BOOTMODE[6:3] = 1001, BOOTMODE[7] is n/a . eMMC…

  • [FAQ] Sitara multicore development and documentation

    I am using an AM62x, AM62Ax, AM62Px, or AM64x. Where can I find documentation about developing software on multiple cores at once? For example, RTOS M4F & Linux A53? We are actively writing new multicore development documentation. We often publish…

  • [FAQ] AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 Custom board hardware design - Reusing TI SK (EVM) design files

    Part Number: AM62A7 Other Parts Discussed in Thread: AM62D-Q1 Hi TI Experts, I am starting a new board design and planning to use TI EVM design files for designing my custom board. Please let me know if you have any suggestions.

  • [FAQ] AM62A3 / AM62A3-Q1 / AM62A1-Q1 Custom board hardware design – Collaterals to Get started

    Part Number: AM62A3 Other Parts Discussed in Thread: AM62D-Q1 , , AM62A7-Q1 , , AM62A7 , SK-AM62A-LP , SYSCONFIG Hi TI Experts, Can you provide a List of collaterals that can be referred when starting a custom board hardware design.

  • [FAQ] TDA4VM: How to do a MAC loopback test with CPSW in TDA4/DRA8 devices

    Part Number: TDA4VM There is some issue in my ethernet link. I wanted to do a sanity check using MAC loopback and see if the MAC is working well or not. Is there an easy way to do this?

  • [FAQ] AM62A7 / AM62A7-Q1 Custom board hardware design – Collaterals to Get started

    Part Number: AM62A7 Other Parts Discussed in Thread: AM62D-Q1 , AM62A3 , , AM62A3-Q1 , , SK-AM62A-LP , SYSCONFIG Hi TI Experts, Can you provide a List of collaterals that can be referred when starting a custom board hardware design.

  • [FAQ] TDA4VM: What are the changes required to fit boot images within 4MB of emmc boot partition ?

    Part Number: TDA4VM What are the changes need to be done in order to fit the boot images within 4MB if the emmc boot partition size is 4MB.

  • [FAQ] AM6442/AM243: How to use the TISCI APIs (READ_KEYCNT_KEYREV & WRITE_KEYREV) to activate the backup key set

    Part Number: AM6442 This FAQ showcase how to use the following TISCI APIs in AM64x/AM243x MCU+SDK - TISCI_MSG_READ_KEYCNT_KEYREV - TISCI_MSG_WRITE_KEYREV

View FAQ threads
  • Threads 197947 Discussions