Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM6442: MCU_RESETZ Reset input - connection of capacitor

    Part Number: AM6442 Tool/software: (Customer Query) Hi TI Experts We are in progress for the Rev.B changes for the V2 SCC schematic and we have made few changes related to the reset circuit for which we need input/confirmation from TI. In…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62Ax / AM62Px / AM62D-Q1 / AM62L / AM64x / AM243x Design Recommendations / Custom board hardware design - Queries related to IBIS model

    Part Number: AM625 Tool/software: Hi TI Experts, Do you have recommendations on using the IBIS model?

  • [FAQ] AM62x & AM64x: How to enable PRU RPMsg on Processor SDK Linux 11.0

    Part Number: PROCESSOR-SDK-AM64X PROCESSOR-SDK-AM62X In Linux kernel 6.12, we remove the separate PRU RPMsg (RPMessage) driver, and use the generic RPMsg driver instead. However, the changes were not complete in time for Linux SDK 11.0. This means that…

  • [FAQ] PROCESSOR-SDK: Getting Started with GPIOs in Linux using the AM62 and AM64 Family Processors

    Part Number: PROCESSOR-SDK-AM62X Other Parts Discussed in Thread: AM62P , AM62L , SK-AM64B , SK-AM62B-P1 , SK-AM62-LP , SK-AM62A-LP , SK-AM62P-LP , TMDS62LEVM , SYSCONFIG Tool/software: The objective of this FAQ is for someone with a TI EVM to enable…

  • [FAQ] TDA4VM: How to enable MCU R5F cores running in split mode in SPL boot flow.

    Part Number: TDA4VM Tool/software: TI SDKs by default configures MCU R5F running in lock step mode, how to configure to run MCU R5F in Split Mode.

  • [FAQ] TDA4VH-Q1: How do I control the quality of service (QoS) and class of service (CoS) settings on TDA4 devices to balance transaction loads and priorities?

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH , J784S4XEVM Tool/software: I'm seeing issues with the display experiencing sync losts when running the TIDL AVP demo. How do I balance the transaction loads and priorities so that the DSS…

  • [FAQ] AM62x, AM62Px, AM62D-Q1, AM64x, AM243x: 4KB Sector Erase Fails

    Part Number: PROCESSOR-SDK-AM62X Tool/software: Greetings, When working with a flash part like S25HL512T or S28HS512T , one will come across Uniform vs Hybrid mode. The points which this FAQ covers is: What is Uniform vs Hybrid Mode for the…

  • [FAQ] SK-AM62A-LP: Is USB OTG possible without PD controller?

    Part Number: SK-AM62A-LP Other Parts Discussed in Thread: AM62P , SK-AM62P-LP , PROCESSOR-SDK-AM62A Tool/software: Hi, For my application, I don't need PD controller for power negotiation. But in SK-AM62A-LP design, PD controller is also used for…

  • [FAQ] TDA4VM: Error while registration of same MAC address with different VLAN to ETHFW server from client.

    Part Number: TDA4VM Tool/software: ETHFW returns error while registration of same MAC address with different VLAN from same client. This issue is observed on 10.1 TI SDK.

  • [FAQ] AM62A7: How to Enable Edge Enhancement on TDA4x/AM6xA

    Part Number: AM62A7 Tool/software: I have my tuned DCC Edge Enhancement binaries, how do I enable EE modules to take effect on my (SK) Edge AI device?

View FAQ threads
  • Threads 199080 Discussions