Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM64x/ AM243x (ALV) / AM62Ax / AM62D-Q1 / AM62Px Design Recommendations / Custom board hardware design – Information on processor core, PLL, VDD_CORE, VDDR_CORE, VPP and other core supplies

    Part Number: AM62L Other Parts Discussed in Thread: AM620-Q1 , AM62P , SYSCONFIG , AM625 , AM623 , AM625-Q1 , AM6421 , SK-AM62B-P1 , AM6442 , AM2432 Tool/software: Hi TI Experts, Please share your inputs on processor core, thermal alert, VDD_CORE…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM64x/ AM243x (ALV) / AM62Ax / AM62D-Q1 / AM62Px Design Recommendations / Custom board hardware design – Information on PADCONFIG bits and PADCONFIG registers default values summary

    Part Number: AM62L Other Parts Discussed in Thread: SYSCONFIG , AM62A3 , AM62P , AM62D-Q1 Tool/software: Hi TI Experts, Could you please elaborate about PADCONFIG register bits and default configurations for PADCONFIG registers.

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM64x/ AM243x (ALV) / AM62Ax / AM62D-Q1 / AM62Px Design Recommendations / Commonly Observed Errors during Custom board hardware design –SD card Interface

    Part Number: AM62L Other Parts Discussed in Thread: AM62P , SYSCONFIG , AM62P5-Q1 Tool/software: Hi TI Experts, Is there a list of design recommendations or commonly observed errors for SD card Interface during Custom board hardware design? Below…

  • [FAQ] PROCESSOR-SDK-AM64X: How to enable constructor / destructor attribute for A53 core using GCC

    Part Number: PROCESSOR-SDK-AM64X Other Parts Discussed in Thread: SYSCONFIG Tool/software: I was using the __attribute__((constructor(x) / destructor(y)) property in C code for A53 core with GCC compiler. the GCC attribute is __attribute__((destructor…

  • [FAQ] How to capture TIFS trace with AM62A Linux SDK

    Part Number: AM62A7 Other Parts Discussed in Thread: SK-AM62A-LP Tool/software: TIFS trace log is a useful debug tool to analyze TIFS firmware operations [1] [2]. There's an issue on capturing TIFS trace log from MAIN_UART1 port with AM62A Linux SDK…

  • [FAQ] AM67: How do I enter PCIe TX compliance mode using Linux?

    Part Number: AM67 Tool/software: I would like to do a PCIe compliance test to see if my AM6x PCIe device meets the standards set by PCI-SIG. What is the procedure to run this test?

  • [FAQ] DRA821U-Q1: How to enable RGMII2 on CPSW5G for TI EVM using the Native Linux Driver?

    Part Number: DRA821U-Q1 Tool/software: How can I enable the RGMII2 interface from the CPSW5G Ethernet switch on the DRA821-Q1 TI EVM using the native Linux driver?

  • [FAQ] TDA4AEN-Q1: How to enable SGMII support on CPSW3G using native Linux Driver?

    Part Number: TDA4AEN-Q1 Tool/software: What is the procedure to enable or activate SGMII interface support for CPSW3G in the native Linux Driver?

  • [FAQ] TDA4VM: gPTP Synchronization Failure over MAC2MAC connection in ETHFW or PDK ENET example.

    Part Number: TDA4VM Tool/software: Facing issue with gPTP synchronization when using a MAC2MAC connection in either the ETHFW or PDK ENET example.

  • [FAQ] TDA4VH-Q1: How do I configure CPSW MAC Port as gPTP clock Master/Slave in Ethernet Firmware (ETHFW) or ENET examples?

    Part Number: TDA4VH-Q1 Tool/software: How do I configure/enable CPSW MAC Port as either gPTP clock Master or clock slave in Ethernet Firmware (ETHFW) or ENET examples?

View FAQ threads
  • Threads 198076 Discussions