• LMV112: Expected output voltage if VDD = VIN = 3.3

  

  Brian Henning

  TI Thinks Resolved

  Part Number: LMV112 Other Parts Discussed in Thread: LMK1C1102 Tool/software: I'm having a hard time understanding the datasheet. Among other things, it claims: • Supply Voltage Range 2.4V to 5V • Slew Rate 110 V/ μ s • Total Supply Current 1.6…

  • 9 months ago
  • Clock & timing
  • Clock & timing forum

• LMV112: Regarding the input voltage of LMV112SD/NOPB

  

  Kangwei Wang

  TI Thinks Resolved

  Part Number: LMV112 Other Parts Discussed in Thread: TIDA-010057 Dear engineers, In TI's Reference Design:TIDA-010057, we found that the power supply voltage of LMV112 is 1.8V, the picture is shown as follows(3.3V is converted to 1.8V and supplies power…

  • over 1 year ago
  • Amplifiers
  • Amplifiers forum

• LMV112: LMV112

  

  Jenitha Ravi

  TI Thinks Resolved

  Part Number: LMV112 Hi I wish to include LMV112SD/NOPB in my design.This buffer output is used as the reference clock for PLL. The supply voltage prefered is 3.2V. So I would like to know about the output voltage swing of this clock buffer and whether…

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

• LMV112: LMV112

  

  eli

  Part Number: LMV112 Other Parts Discussed in Thread: CDCLVC1102 , LMK00804B , LMK00105 using the TI part clock buffer LMV112SD/NOPB input = Oscillator 8.192MHz output = bad waveform why output look like this? what other TI clock buffer part…

  • over 8 years ago
  • Clock & timing
  • Clock & timing forum

• LMV112: can i put series resistor between EN and VDD

  

  VAIBHAV RAJGURU

  Part Number: LMV112 Dear Sir, I am using LMV112 in project, application note show's EN1 and EN2 pin is connected to VDD. so i am putting series resistor between EN and VDD & transistor for EN control will it work? Regards, Vaibhav Rajguru

  • over 5 years ago
  • Clock & timing
  • Clock & timing forum

• LMV112: Output seems to disappear 10Mhz or Above

  

  Paul Applegarth

  Part Number: LMV112 I am Using the Part in a Circuit, it will be feed from an Oscillator eventually, but at the moment a digital Arb/Signal Generator. I have soldered 3 up on my boards, and the output feeds a TTL Counter, and a RAM - FIFO Clock. I…

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• LMV112: Thermal pad grounded or not?

  

  Glenn Andrews

  Resolved

  Part Number: LMV112 Hi, Do you ground the thermal pad under the chip, or leave it floating? Thanks, Glenn

  • Resolved

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum

• LMV112 Dual Clock Buffer

  

  GMC

  TI Thinks Resolved

  Other Parts Discussed in Thread: LMV112 , CDC3RL02 , CDCLVC1102 , LMK00804B , LMK00105 Hello, Can LMV112 Clock Buffer be used with CMOS Oscillator (like DSC1003)? Thank you, GMC

  • over 9 years ago
  • Clock & timing
  • Clock & timing forum

• LMV112 technical specifications

  

  JEFF CRISPINO

  Other Parts Discussed in Thread: LMV112 We are looking for the phase noise/jitter specifications for LMV112. It doesn't appear to be in the datasheet. Does this information happen to be available?

  • over 11 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• Question about LMV112

  

  HM

  Resolved

  Other Parts Discussed in Thread: LMV112 Hi, I have some questions about LMV112. 1) I have a plan to disribute LPC clock (33MHz single end) from mother board to two lines. Above connection is correct? 2) On the datasheet of LMV112, it is…

  • Resolved

  • over 11 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.