• Threads 50504 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM2434: GPIO (pins) esd protection and maximum allowed voltages.

    Part Number: AM2434 Tool/software: I'm trying to find answers to the following questions about all signal ( digital and analog ) pins and could not find that specific information in the datasheet. Does every pin have a diode to it's respective…

  • [FAQ] AM2611: Build project error

    Part Number: AM2611 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Dear expert, Two of my customers use CCS12.8.1 and download the CSP, follow the instruction to replace the ccsbase. One customer loads the demo project, but there is an…

  • [FAQ] MCU-PLUS-SDK-AM263PX: AM263P4: SBL Fails when using sbl ospi and error while using ospi examples

    Part Number: AM263P4 Other Parts Discussed in Thread: MCU-PLUS-SDK-AM263PX , SYSCONFIG Tool/software: MCU-PLUS-SDK-AM263PX Following examples are failing in SDK 10.01.00 version in am263px-cc PROC159A board: sbl ospi ospi examples mcan_external_read_write…

  • [FAQ] AM263P4/AM2612: Adding Support for Custom Flash in Uniflash tool using MCU PLUS SDK AM26x

    Part Number: AM2612 Other Parts Discussed in Thread: UNIFLASH Tool/software: Note: Valid for only AM263Px and AM261x devices Hi Expert, How do I add custom flash programming support in Uniflash tool using MCU PLUS SDK.

  • [FAQ] TMS570LC4357: DCAN remote frame

    Part Number: TMS570LC4357 Tool/software: 1. What is the remote frame used for? 2. What is the difference between remote frame and data frame? 3. Is a transmit object used for remote frame? 4. Should the DLC of remote frame be identical to the DLC…

  • [FAQ] TMS570LS1224: N2HET emulated SCI might get a corrupted byte after receiving 6~7 bytes of data

    Part Number: TMS570LS1224 Tool/software: The TMS57LS12x and TMS570LS07x have one LIN/SCI. If an extra SCI is required, we can implement an SCI using N2HET module. TI provides example code of N2HET emulated SCI. I got several feedbacks that the N2HET…

  • [FAQ] TMS570LC4357: HALCOGEN CSP Unit Test with TAU and LDRA

    Part Number: TMS570LC4357 Other Parts Discussed in Thread: HALCOGEN Tool/software: 1. Why does the TCF generation fail? 2. What are the possible reasons for build failure? 3. When the test execution hung, what should we do? 5. Can I use HalCoGen…

  • [FAQ] LP-AM243: Routing GPIO interrupts to PRU core

    Part Number: LP-AM243 Other Parts Discussed in Thread: SYSCONFIG Tool/software: I am trying to modify the gpio_input_interrupt example for the R5F0-0 core to direct the GPIO interrupt to the PRU core. Requirement: GPIO1_0 interrupt -> MAIN_GPIOMUX_INTROUTER0_OUTP_18…

  • [FAQ] MCU-PLUS-SDK-AM243X: Can AM243x use OSPI PSRAM as a memory expansion?

    Part Number: MCU-PLUS-SDK-AM243X Tool/software: Hi, can AM243x OSPI work with a PSRAM? If so, which are the HW and SW modifications required? When is OSPI PSRAM a good fit as memory expansion?

  • [FAQ] TMS570LC4357: How to set ESM error pin to High

    Part Number: TMS570LC4357 Tool/software: After triggering an ESM fault, performing a warm reset without clearing the ERR pin status by writing esmREG -> EKR = 5 after rebooting, writing t writing esmREG -> EKR = 5 has no effect, the counter does…

View FAQ threads