Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DRA821: SPL BOOT without A72 SPL on J7200 on 10.1 SDK

    Part Number: DRA821 Tool/software: How to enable Falcon Boot Mode on J7200? Boot Flow: R5 SPL -> ATF -> OPTEE -> U-BOOT -> Kernel Regards Gokul

  • [FAQ] How to avoid crashing the DM R5F when writing custom DM R5F firmware

    Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px The primary role of the Device Management (DM) R5F core is to run the DM task. However, on some devices (not all devices!), TI supports writing custom code to run on the DM R5F, alongside the…

  • [FAQ] SBL boot: How to find the DM R5F firmware that is loaded by SBL

    Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px The primary role of the Device Management (DM) R5F core is to run the DM task. However, there may be other non-DM code running on the DM R5F, alongside the DM task. The firmware running on the…

  • [FAQ] TDA4AL-Q1: Large byte transfer

    Part Number: TDA4AL-Q1 Tool/software: Example application on SDK 10.0 to show large byte transfer between CDD IPC(MCU1_0) and Linux (A72) using cdd_ipc_rc_linux ,rpsmg_char_simple applications on J721S2 ?

  • [FAQ] How to check if Linux can communicate with a non-Linux core through RPMsg

    Other Parts Discussed in Thread: AM67 , AM67A Before Linux can communicate with a non-Linux core over the RPMsg inter-processor communication (IPC) protocol, several things needs to be true: 1) RPMsg between Linux and the non-Linux core must be supported…

  • [FAQ] Linux: How to check what binary is running on the DM R5F

    Other Parts Discussed in Thread: AM67 , AM67A Parts Discussed in Thread: AM62x, AM62Ax, AM62Dx, AM62Px, AM67, AM67A The primary role of the Device Management (DM) R5F core is to run the DM task. However, there may be other non-DM code running on the…

  • [FAQ] TDA4VM-Q1: How to enable cross domain UART access from PDK applications.

    Part Number: TDA4VM-Q1 Tool/software: On custom boards where UART instances are limited, how can I route debug output from my application running in one domain to a UART instance available in different domain? Specially, I want to enable cross-domain…

  • [FAQ] EDGE-AI-STUDIO: TIDL RTOS tool vs edgeai-tidl-tools

    Part Number: EDGE-AI-STUDIO Tool/software: Model importing in TI has two sets of tools due to historical reasons. These two sets has developed in parallel for a long time. Here is an explanation of the similarity and difference of the two tools. …

  • [FAQ] What is Active Slot bitmask, Data Bitmask, and Transaction Count in MCASP?

    Part Number: AUDIO-AM62D-EVM AUDIO-AM275-EVM Other Parts Discussed in Thread: SYSCONFIG Tool/software: 1. While configuring McASP through sysConfig, I found that when the num of slots set as 2, the active slot bitmask can only below 3. What is this…

  • [FAQ] Not able to return from infinity loop in C7 core by changing the loop variable using CCS

    Part Number: AUDIO-AM275-EVM Tool/software: I am not able to return from infinity loop in C7x core by changing the loop variable from the Variables tab in CCS. In the following code - void loop_forever() { volatile uint32_t loop = 1U; while(loop…

View FAQ threads
  • Threads 198362 Discussions