Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM6x: Using multilib to allow running 32-bit binaries on Yocto Dunfell-based v8.x SDKs for Sitara 64-bit MPUs

    Part Number: AM62x, AM62Ax, AM64x, AM65x Overview Multilib is one of the solutions allowing users to run applications built for various application binary interfaces (ABIs) of the same architecture. One use of this is to run 32-bit applications built…

  • [FAQ] AM6x/AM335x/AM437x: Using a Yocto-internal toolchain for target image builds and cross-development SDK installer generation with Yocto Dunfell-based v8.x SDKs for Sitara MPUs

    Part Number: AM335x, AM437x, AM62x, AM62Ax, AM64x, AM65x Overview This E2E FAQ shows an alternative approach of how to use an Yocto-internal toolchain for image builds as well as for the associated SDK installer generation that contains the cross…

  • [FAQ] 66AK2H14: I2C Boot Parameter Table correction in datasheet, SPRS866G

    Part Number: 66AK2H14 Hi, Please provide the correction in the " I2C Boot Parameter Table in datasheet, SPRS866G" for 66AK2Hxx devices.

  • [FAQ] TDA4VM: Does SDK8.5 MCAL CDDIPC supports communication with A72 running Linux

    Part Number: TDA4VM If not, Is there a patch to support communication with A72 running Linux ?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62P / AM62P-Q1 Custom board hardware design – OLDI (Open LVDS Display Interface) capabilities

    Other Parts Discussed in Thread: AM620-Q1 , AM62P , AM625 , SK-AM62P-LP Hi TI Experts, I have the below queries regarding the OLDI interface Supported display configurations. Query regarding 8-lane, 4-lane and electrical compatibility. Is there…

  • [FAQ] TDA4VM: Ability to change boot mode in SW

    Part Number: TDA4VM I do not have UART boot mode on my custom board due to lack of switch / pins which can configure the boot mode. Is there a way by which I can change the boot mode in software using gel scripts?

  • [FAQ] PROCESSOR-SDK-J721E: How to enable trace/assert in VHWA drivers?

    Part Number: PROCESSOR-SDK-J721E By default trace and assert functionalities are disabled in the VHWA PDK driver. This article explains how to enable it in the VHWA drivers.

  • [FAQ] TDA4VM-Q1: TDA4 Drive Strength Controls

    Part Number: TDA4VM-Q1 What are the drive strength controls for TDA4?

  • [FAQ] How to run OTP Keywriter on SK-AM64B

    Part Number: SK-AM64B Other Parts Discussed in Thread: TCA9538 Hello TI, I’m currently working on TI’s SK-AM64B boards, trying to move them from HS-FS to HS-SE mode. To do so, I’m using the OTP Keywriter tool with MCU+ SDK for AM64x in its latest…

  • [FAQ] AM62X-PET-CALC: AM62x Sysconfig power confict warning

    Part Number: AM62X-PET-CALC Hi TI When i finish the PINMUX config and power domain config, there is confict message show as below，Can i suppress these two warning ? As the MCU GPIO is 3v3 level ,so i connect the VDDSHV_MCU to 3v3 domain. BR…

View FAQ threads
  • Threads 197922 Discussions