Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM6x/AM335x/AM437x: Using a Yocto-internal toolchain for target image builds and cross-development SDK installer generation with Yocto Dunfell-based v8.x SDKs for Sitara MPUs

    Part Number: AM335x, AM437x, AM62x, AM62Ax, AM64x, AM65x Overview This E2E FAQ shows an alternative approach of how to use an Yocto-internal toolchain for image builds as well as for the associated SDK installer generation that contains the cross…

  • [FAQ] 66AK2H14: I2C Boot Parameter Table correction in datasheet, SPRS866G

    Part Number: 66AK2H14 Hi, Please provide the correction in the " I2C Boot Parameter Table in datasheet, SPRS866G" for 66AK2Hxx devices.

  • [FAQ] TDA4VM: Does SDK8.5 MCAL CDDIPC supports communication with A72 running Linux

    Part Number: TDA4VM If not, Is there a patch to support communication with A72 running Linux ?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62P / AM62P-Q1 Custom board hardware design – OLDI (Open LVDS Display Interface) capabilities

    Other Parts Discussed in Thread: AM620-Q1 , AM62P , AM625 , SK-AM62P-LP Hi TI Experts, I have the below queries regarding the OLDI interface Supported display configurations. Query regarding 8-lane, 4-lane and electrical compatibility. Is there…

  • [FAQ] TDA4VM: Ability to change boot mode in SW

    Part Number: TDA4VM I do not have UART boot mode on my custom board due to lack of switch / pins which can configure the boot mode. Is there a way by which I can change the boot mode in software using gel scripts?

  • [FAQ] PROCESSOR-SDK-J721E: How to enable trace/assert in VHWA drivers?

    Part Number: PROCESSOR-SDK-J721E By default trace and assert functionalities are disabled in the VHWA PDK driver. This article explains how to enable it in the VHWA drivers.

  • [FAQ] TDA4VM-Q1: TDA4 Drive Strength Controls

    Part Number: TDA4VM-Q1 What are the drive strength controls for TDA4?

  • [FAQ] How to run OTP Keywriter on SK-AM64B

    Part Number: SK-AM64B Other Parts Discussed in Thread: TCA9538 Hello TI, I’m currently working on TI’s SK-AM64B boards, trying to move them from HS-FS to HS-SE mode. To do so, I’m using the OTP Keywriter tool with MCU+ SDK for AM64x in its latest…

  • [FAQ] AM62X-PET-CALC: AM62x Sysconfig power confict warning

    Part Number: AM62X-PET-CALC Hi TI When i finish the PINMUX config and power domain config, there is confict message show as below，Can i suppress these two warning ? As the MCU GPIO is 3v3 level ,so i connect the VDDSHV_MCU to 3v3 domain. BR…

  • [FAQ] AM64X: How to Run MCU+ SDK GPIO_INPUT_INTERRUPT example for R5FSS0-0 with Linux running on A53

    Part Number: AM6442 Problem Description The MCU+ SDK comes with a GPIO_INPUT_INTERRUPT example for R5FSS0-0. This example configures a GPIO pin to generate an interrupt and then registers an interrupt handler to service the GPIO interrupt. This example…

View FAQ threads
  • Threads 198410 Discussions