Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: How to switch channels using the mosaic node

    Part Number: TDA4VM As the mosaic node takes in object array as input and does not have vxreplicateNode implemented, how to enable switch channel in this node?

  • [FAQ] TDA4VM: IPC Debug steps

    Part Number: TDA4VM Hello, May i know how to debug IPC and see if its working fine? Regards Tarun Mukesh

  • [FAQ] PROCESSOR-SDK-AM57X: How do I build the 08.02.01.00 SDK using Yocto?

    Part Number: PROCESSOR-SDK-AM57X The Documentation for building the 8.2 SDK is outdated and does not work as is in 1.2. Building the SDK

  • [FAQ] AM6442 / AM6441 / AM6422 / AM6421 / AM6412 / AM6411 Custom board hardware design - Design and Review notes for Reuse of TMDS64EVM Schematics

    Part Number: AM6442 Other Parts Discussed in Thread: TMDS64EVM , SYSCONFIG TMDS64EVM Hi TI Experts, I am starting a new board design and planning to use TI EVM design files for designing my custom board. https://www.ti.com/tool/TMDS64EVM Please…

  • [FAQ] AM620-Q1 / AM625-Q1 Custom board hardware design - Design and Review notes for Reuse of SK-AM62-LP Schematics

    Part Number: AM625-Q1 Other Parts Discussed in Thread: SK-AM62-LP , SK-AM62B-P1 , SK-AM62B , SYSCONFIG , AM625 Hi TI Experts, I am starting a new board design and planning to use TI Starter Kit (SK) design files for designing my custom board. https…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62Ax / AM62D-Q1 / AM62Px / AM64x / AM243x Design Recommendations / Commonly Observed Errors during Custom board hardware design – SOC peripherals and IOs connection when not used

    Part Number: AM625 Other Parts Discussed in Thread: AM62L Hi TI Experts, I am designing my custom board using TI AM62x family of processors. I have a few queries. 1. I am expecting to not use some of the SOC peripherals. Do you have a recommendation…

  • [FAQ] PROCESSOR-SDK-J721S2: Enable DP->HDMI adaptor on SDK9.x release

    Part Number: PROCESSOR-SDK-J721S2 This article provides the changes required to enable DP->HDMI adaptor on SDK9.x release.

  • [FAQ] AM623: MCU_OSC0_XI starts timing slot is not correct

    Part Number: AM623 Hi, TI Expert [Problem] : We found "MCU_OSC0_XI/MCU_OSC0_OUT" clock starts timing "forward" than VDD_CORE voltage pull high. (Customized board) Normal timing should be like this chart. MCU_OSC0_XI/MCU_OSC0_OUT starts after VDD_CORE…

  • [FAQ] AM6x: UART Boot and Download Speed Optimizations (25+% !!!)

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM64B , SK-AM62B Overview The UART boot mode available on AM6x processors (and other similar TI devices) is a valuable tool often used during development and board bringup. To load the initial…

  • [FAQ] AM62A7: Is it possible to adjust the timing of RMII TXD? RMII connection with Ethernet Switch IC - MAC-MAC RMII loopback

    Part Number: AM62A7 Hello. I'm developing custom board which has RMII connection with Ethernet Switch IC. The AM62A and the Ethernet switch IC are connected via MAC-to-MAC mode. The message 'eth0 Link is up' appears, but the ping command fails. I…

View FAQ threads
  • Threads 198423 Discussions