Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: OSPI boot: TISCI config ring fail error with SDK 7.3

    Part Number: TDA4VM Hi, OSPI boot with SDK 7.3 is functional but before getting to u-boot prompt we encounter a lot of error messages. TISCI config ring fail (-19) ring_idx 6 TISCI config ring fail (-19) ring_idx 124 … … TISCI config ring fail…

  • [FAQ] TDA4VM: How to ensure that dependent module drivers are probed before depending driver

    Part Number: TDA4VM In Linux how to ensure that all the dependent drivers are probed before depending driver is probed such that the driver probe does not error out due to the dependent devices being absent. Ex: Custom TDA4 Board with PPS signal connected…

  • [FAQ] AM6548: Does AM65 support Ethernet Switch on Linux/RTOS

    Part Number: AM6548 Does AM65 support Ethernet Switch on Linux or RTOS platform ?

  • [FAQ] PROCESSOR-SDK-J721E: How to run display (any PDK) example from SBL?

    Part Number: PROCESSOR-SDK-J721E This article explains how to build and run DSS example.

  • [FAQ] TDA4VM: J721e:/J7200: How to switch console to a different UART instance

    Part Number: TDA4VM I want to switch console to a different UART instance. I do not have MAIN_UART0 wired out can i move all the prints to MCU_UART0? If yes how do I do that?

  • [FAQ] AM6548: Under linux, how to configure the device tree to enable the DPI display interface output of the am6548 chip

    Part Number: AM6548 I downloaded the latest sdk of the am65xx series, but I don’t know how to configure the dss driver to enable the DPI display interface output of the am6548 chip.

  • [FAQ] AM6548: How to configure 512MB*2 DDR ram in uboot?

    Part Number: AM6548 Hi Ti, We will use AM6548 SR2.0 to bring up our evm board, and there will be 512MB*2, total is 1GB ddr4 in our evm. In this case, we have two question want to confirm with you. 1. How to modify the memory region in k3-am654…

  • [FAQ] TDA4VM: How to enable NFS On PSDKRA

    Part Number: TDA4VM Hi, I am using the below instructions from PSDKRA for NFS but it does not seem to working: https://software-dl.ti.com/jacinto7/esd/processor-sdk-rtos-jacinto7/latest/exports/docs/vision_apps/docs/user_guide/RUN_INSTRUCTIONS.html#run_steps_linux_nfs…

  • [FAQ] DRA821U: 5 port switch working with linux

    Part Number: DRA821U Hi I like to get the 5 port switch to work on the TI EVM? it looks like i need some binary to run on the MCU2_0 to get the switch to work? why do i need that? does that mean if I use the 5 port switch i can't use the MCU2_0? Please…

  • [FAQ] TDA4VM: GPIO interrupt use DMA

    Part Number: TDA4VM Other Parts Discussed in Thread: SYSBIOS dear experts： I want use the GPIO input calture function and use the DMA function. can you provide us the examble or demo ? I also check the path to the example is at <SDK_PATH>/psdk_rtos_auto_j7_07_00_00_11…

View FAQ threads
  • Threads 198383 Discussions