Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM6442: Can AM6442 support this kind of programming method?

    Part Number: AM6442 Hi Expert, can we use this way to program AM64x boot SPI FLASH? When we want to program,we short the jumper to short the MCU_PORz reset to GND,to let AM64 all pins to initial states,which can release the QSPI pins. Then we…

  • [FAQ] TMS320C6678: How to configure GPIO interrupt and test on Keystone I devices - C6678 ?

    Part Number: TMS320C6678 Hi How to configure GPIO interrupt and test on Keystone I devices - C6678 ?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62Ax / AM62D-Q1 / AM62Px / AM64x / AM243x Design Recommendations / Commonly Observed Errors during Circuit Optimization of Custom board hardware design

    Part Number: AM625 Hi TI Experts, Please let me know if you have some specific recommendations or care-about for Circuit Optimization of Custom board hardware design .

  • [FAQ] TDA4VH-Q1: Performing ECC SEC/DED tests on R5F cache memories

    Part Number: TDA4VH-Q1 Other Parts Discussed in Thread: TDA4VH Is ECC (SEC/DED) testing possible on R5F internal cache memories? If yes, please provide the steps to do so.

  • [FAQ] TDA4VH-Q1: Analysis on Latency Wave521CL CODEC IP

    Part Number: TDA4VH-Q1 What information is available of encoder/decoder latency on the Wave521CL CODEC IP?

  • [FAQ] AM6422: am64x internal clock as Ethernet PHY Clock source CLKOUT0 EXT_REFCLK1

    Part Number: AM6422 Other Parts Discussed in Thread: DP83867IR , SYSCONFIG Hello, I am working with the am64x and the industrial communication SDK. I am trying to run the ethercat_slave_beckhoff_ssc_demo. The development board I am using does not provide…

  • [FAQ] Board bring up tips for Sitara devices (AM64x, AM243x, AM62x, AM62L, AM62Ax, AM62D-Q1, AM62Px)

    Other Parts Discussed in Thread: AM625SIP , AM62D-Q1 , AM625 The page provides tips on debugging initialization and boot up issues with the following devices: AM64x AM243x AM62x/AM625SIP AM62Lx AM62Ax AM62D-Q1 AM62Px If this page doesn…

  • [FAQ] TDA4VM: How to address the assertion Issue from EthFw, due to race condition between multiple client requests for EnetMcm Module Server Task.

    Part Number: TDA4VM How to address the assertion Issue from EthFw, due to race condition between multiple client requests for EnetMcm Module Server Task.

  • [FAQ] AM625 / AM623 Custom board hardware design - Design and Review notes for Reuse of SK-AM62B Schematics

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62B , SK-AM62B-P1 , Hi TI Experts, I am starting a new board design and planning to use TI Starter Kit (SK) design files for designing my custom board. https://www.ti.com/tool/SK-AM62B …

  • [FAQ] AM6442: SERDES Common Mode Voltage, Seeing 400mv centerpoint in simulation

    Part Number: AM6442 Hello, I am trying to understand what voltage levels I am looking at with the AM6442 SERDES driver. I am using the IBIS-AMI model in HYPERLYNX I am seeing the common mode output voltage swing from 200 to 600 mV with a centerpoint…

View FAQ threads
  • Threads 199049 Discussions