Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM69: How can I assign interface ID to CAN modules

    Part Number: AM69 I want to use the CAN interfaces can0, can1, can2 and can3 from Linux user space and hence want hardcode the IDs. Currently based on the probe sequence from the Kernel, these get assigned randomly. I tried using aliases in the Kernel…

  • [FAQ] AM64X/AM62X/AM62AX : Configuring the ESM module from SDL and setting the ESM Bit Fields to enable the ESM Error events

    Part Number: AM64x/AM62x/AM62Ax This FAQ mainly explains how to configure the ESM module in the SDL and enabling the error events which trigger the ESM interrupts. It also shows how to set a interrupt priority for an ESM event and enable an external…

  • [FAQ] J721EXSOMXEVM: How to work around errata i2086 for PCIe switches and multifunction devices for J721E/TDA4VM/DRA829?

    Part Number: J721EXSOMXEVM Other Parts Discussed in Thread: TDA4VM , TDA4VL , TDA4VH , DRA829 There is a known errata for J721E/TDA4VM/DRA829 where connecting a PCIe switch, or multi-function PCIe device would cause a system abort. This issue only affects…

  • [FAQ] TDA4AL-Q1: CAN Profiling Application failed to operate in Tx only or External Loopback and Polling mode or interrupt mode.

    Part Number: TDA4AL-Q1 Hi, Can you provide patch to fix the issue on SDK 8.6 ? Regards Tarun Mukesh

  • [FAQ] How do I bring/brought up Ethernet interfaces for Main Domain CPSWnG in Linux from SDK Version 9.0 and above?

    Other Parts Discussed in Thread: DRA821 , DRA829 , TDA4VM , TDA4VH , TDA4VL How do I bring/brought up Ethernet interfaces for Main Domain CPSWnG in Linux from SDK Version 9.0 and above?

  • [FAQ] Setting up Auto Exposure (AE) for your image sensor with TDA4/AM6xA ISP (VPAC)

    How can I set up AE for an camera/sensor with TDA4/AM6xA ISP (VPAC)?

  • [FAQ] Where can i find MCAL configurator package and EB Tresos studio for Jacinto devices ?

    Part Number: TDA4VM Hello, Customers typically asks below 2 queries on MCUSW Configurator 1. How to get access for MCAL Configurator package "MCUSW_XX_YY_ZZ_BB_CONFIG-windows-installer.exe" ? 2. How to request an EB Tresos license for MCUSW…

  • [FAQ] AM6412: AM64x SPI D0 and D1 - MISO/MOSI

    Part Number: AM6412 Hi, As per the AM64x Sitara Processors datasheet, both MCSPI and MCU_MCSPI D0 and D1 signals defined as IO pin type We need to develop a product based on the AM6412 processor While interfacing any slaves devices with the AM6412…

  • [FAQ] J721S2XSOMXEVM: How to enable main domain watchdog?

    Part Number: J721S2XSOMXEVM Other Parts Discussed in Thread: TDA4VM The j721e/TDA4VM has SOC watchdog enabled. How to enable the same on J721s2?

  • [FAQ] DCC Tuning Tool V3.2 for VPAC on TDA4x and AM6xA Devices

    Hi everyone, DCC Tuning Tool V3.2 for TDA4x and AM6xA has been released in 09/2024. You may find it now in your secure resource section on ti.com. If you have no access or expired access, you may apply here -- http://www.ti.com/drr/opn/ADAS-SW-IMAGING…

View FAQ threads
  • Threads 198299 Discussions