Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] EVMK2GX: U-boot build steps for K2G

    Part Number: EVMK2GX How to build u-boot for K2G? from the package "PROCESSOR-SDK-LINUX-K2G".

  • [FAQ] SK-TDA4VM: How do I use the CAN bus headers on SK-TDA4VM using Edge AI SDK?

    Part Number: SK-TDA4VM Other Parts Discussed in Thread: TDA4VM The SK-TDA4VM has 4 CAN bus interface. How can these be used?

  • [FAQ] SK-TDA4VM: How do I enable and debug IMX390 + fusion board not working with Edge AI SDK

    Part Number: SK-TDA4VM I have connected the SK-TDA4VM board with fusion board and IMX390. I am following the SDK documentation on enabling the camera: https://software-dl.ti.com/jacinto7/esd/processor-sdk-linux-sk-tda4vm/08_02_00/exports/docs/getting_started…

  • [FAQ] PROCESSOR-SDK-J721E: How to use DRU channels for config data in VISS

    Part Number: PROCESSOR-SDK-J721E For heterogeneous camera processing, VISS internally uses UDMA channel for saving and restoring the configuration almost on every frame. This article explains how VISS driver can be changed to use DRU channels for saving…

  • [FAQ] 66AK2H12: Linux build from Processor Linux SDK

    Part Number: 66AK2H12 Other Parts Discussed in Thread: 66AK2H14 , , 66AK2H06 How to build Boot Monitor, Linux, Device tree, and Kernel from "Processor-SDK-Linux" for K2H Family devices (EVMK2H, 66AK2H12, 66AK2H06, 66AK2H14)?

  • [FAQ] 66AK2H12: Linux Flashing steps for K2HK family processor

    Part Number: 66AK2H12 How to boot Linux on K2E using NFS from the package "PROCESSOR-SDK-LINUX-K2HK" ?

  • [FAQ] AM6421:VDD_CORE Voltage selection

    Hi, 1.VDD_ Core can use 0.75V and 0.85v power supply. What is the difference between these two voltages? What is the effect of choosing different voltages？ 2.Can VDD_CORE, VDDR_CORE, VDD_MMC0,VDD_DLL_MMC0, VDDA_0P85_SERDES0, VDDA_0P85_USB0 all be…

  • [FAQ] SK-AM62: How to flash eMMC using USB DFU on AM62x-SK E2

    Part Number: SK-AM62 Other Parts Discussed in Thread: CSD , AM62P5 This thread discusses the process of full Linux eMMC flashing using USB DFU on an AM62x-SK E2 board. A Linux host PC with the tool dfu-util is required.

  • [FAQ] SK-AM62: FAQ: How do I set the DIP switches to get a certain boot mode?

    Part Number: SK-AM62 The AM62x SK-EVM has two 8-position DIP switches to set the SoC boot mode and related parameters. How do these switches correspond to the boot mode pins documented in the TRM?

  • [FAQ] TDA4VM: Using PDK GPIO driver

    Part Number: TDA4VM Hi, Can someone share simple steps to toggle GPIO and configuring GPIO interrupt using PDK GPIO driver.

View FAQ threads
  • Threads 197810 Discussions