Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How to use K3 resource partitioning tool with Processor SDK v9.0 or v9.1?

    Other Parts Discussed in Thread: SYSCONFIG Hi Team, I am using Processor SDK Linux v9.0 or v9.1 for development. I want to do resource allocation between the cores, but these files from SDK 8.x are no longer in the SDK: board-support/k3-image-gen tool…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM62L / AM62Ax / AM62D-Q1 / AM62Px Design Recommendations / Commonly Observed Errors during Custom board hardware design – OSPI/QSPI MEMORY Interface

    Other Parts Discussed in Thread: AM62P , AM62L , AM625 , TDA4VM , AM62A3 , AM6441 Hi TI Experts, Is there a list of design recommendations or commonly observed errors for OSPI/QSPI (OSPI0) MEMORY Interface during Custom board hardware design?

  • [FAQ] TDA4VM: Enable CSI-TX output instead of DSS output in the capture demos of vision_apps

    Part Number: TDA4VM How to send the captured data over csi-tx instead of DSS in the vision_apps capture demos?

  • [FAQ] AM6442: Minimum value of UART Input Slew Rate

    Part Number: AM6442 Hi, My customer has some questions about UART Input Conditions. Could you please answer their questions below. 1. Is there any chance to relax the minimum value of UART Input slew rate requirement ? 2. What kind of problem…

  • [FAQ] AM62P, AM62P-Q1 Custom board hardware design - FAQs related to Processor collaterals, functioning, peripherals, interface and Starter kit

    Part Number: AM62P Other Parts Discussed in Thread: AM62D-Q1 , , , TMUX1308-Q1 , TPS65224-Q1 Hi Board designers, Refer FAQs listed below related to custom board design for AM62Px processor family that could be used along with other available design…

  • [FAQ] AM62P / AM62P-Q1 Custom board hardware design - Reusing TI SK (EVM) design files

    Part Number: AM62P Hi TI Experts, I am starting a new board design and planning to use TI SK (EVM) design files for designing my custom board. Please let me know if you have any suggestions.

  • [FAQ] AM62P / AM62P-Q1 Custom board hardware design – I2C interface

    Part Number: AM62P Other Parts Discussed in Thread: AM62A7 , , AM6442 , SK-AM64B Hi TI Experts, I have the below queries regarding the I2C interface: Need information on the number of I2C interfaces available. Termination of I2C interfaces when…

  • [FAQ] AM62P / AM62P-Q1 Custom board hardware design – Collaterals to Get started

    Part Number: AM62P Other Parts Discussed in Thread: , AM62D-Q1 , , SYSCONFIG Hi TI Experts, Can you provide a List of collaterals that can be referred when starting a custom board hardware design.

  • [FAQ] PROCESSOR-SDK-AM57X: What IPC version for do I use when using Linux SDK 08.02.01.00?

    Part Number: PROCESSOR-SDK-AM57X Utilizing the correct version of IPC will help your IPC applications function correctly. One key point is that one cannot mix and match SDK RTOS versions with different Linux SDK versions. The Linux kernel remoteproc…

  • [FAQ] AM6442: ADC0_DIG_TEST[0-7]. when a digital inputs, can these eight be considered as MAIN GPIO and/or interrupt inputs at 1.8V logic

    Part Number: AM6442 We are opting to not use the ADC module for ADC conversion. Per the TRM document SPRUIM2G section 12.1.1.4.2.2 we want to set GPI_MODE_EN = 1. Can these 1.8V logic level inputs we used either as interrupts to the A53 or R5 cores…

View FAQ threads
  • Threads 197701 Discussions