Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How to flash and boot u-boot from parallel GPMC NAND on AM64x

    Part Number: AM6442 Other Parts Discussed in Thread: TMDS64EVM Tool/software: AM64x boot ROM supports booting from parallel GPMC NAND. From "4.4.10 GPMC NAND Boot" in AM64x TRM "AM64x ROM only supports boot from ONFI 1.0 compatible 8 bit parallel…

  • [FAQ] Using DDR IBIS Models for AM64x, AM243x (ALV), AM62x, AM62L, AM62Ax, AM62D-Q1, AM62Px

    Other Parts Discussed in Thread: SYSCONFIG The DDR Controller and PHY in Sitara processors is a flexible interface which can be used with LPDDR4 or DDR4. There are many settings available to fine-tune the signal timing on this interface. These settings…

  • [FAQ] PROCESSOR-SDK-AM62X: Question about AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP DDR MARGIN TEST Tool

    Part Number: PROCESSOR-SDK-AM62X Other Parts Discussed in Thread: SK-AM62-LP , SK-AM62A-LP Tool/software: Hi I want to use the DDR Margin Test Tool on the AM62x-SK-EVM for testing, but I encountered an issue in the red step while following the readme…

  • [FAQ] PROCESSOR-SDK-AM64X: PCIE communication using AM64x/AM243x

    Part Number: PROCESSOR-SDK-AM64X Tool/software: Hi Team, I want to use two AM64x board for PCie communication. One EVM acts as root complex and other EVM acts as a Endpoint. I am using PE-FLEXI-G2-MMCX-12-TII. I want to verify memory read…

  • [FAQ] TDA4VM: How to create lens shading correction LUT for VPAC-VISS-LSC?

    Part Number: TDA4VM Tool/software: How can I create lens shading correction LUT for VPAC-VISS-LDC?

  • [FAQ] AM620-Q1: Inputs required for DDR4 Signal Integrity Simulation

    Part Number: AM620-Q1 Tool/software: In one of our projects, we are using AM620-Q1_FCBGA441 where there is a necessity of DDR4 interface. We need help from Texas side for the following details for signal integrity simulation: 1. on-die package…

  • [FAQ] AM6421: MCSPI CLOCK output not as expected for frequency > 6.25 MHz

    Part Number: AM6421 Other Parts Discussed in Thread: SYSCONFIG , AM6442 , , AM6422 , TMDS64EVM , SK-AM64B Tool/software: Hello, I found some issues when debugging MCSPI – FRAM. Please help give solutions to resolve these issues, thanks. Currently…

  • [FAQ] Most common problems encountered when developing camera applications on the AM6x

    Part Number: AM62A7 Other Parts Discussed in Thread: AM62P , AM69A , AM68A , AM67 , , AM625 , AM623 Tool/software: What are the most common problems encountered when developing camera applications on the AM6x (AM62/AM62A/AM62P/AM67/AM68A/AM69A) and…

  • [FAQ] What are the common reasons V4L2 based applications fail to capture images from a probed CSI sensor?

    Part Number: AM62A7 Other Parts Discussed in Thread: AM67 , Tool/software: I connected my CSI camera to my board and the sensor has successfully probed, but I'm not able to capture images from the camera. None of "v4l2-ctl --stream-mmap", "yavta -c…

  • [FAQ] What are the common reasons a CSI sensor fails to probe in V4L2 environment?

    Part Number: AM62A7 Other Parts Discussed in Thread: AM62P , , AM67 , AM625 , AM623 Tool/software: I connected my CSI camera to my board, but the sensor didn't probe. What are the possible reasons the sensor doesn't probe? Other parts: AM62A3 ,…

View FAQ threads
  • Threads 197586 Discussions