Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 / AM62L / AM62P / AM62P-Q1 / AM64x / AM243x Custom board hardware design – S-parameter and IBIS model of IO-buffer

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , Tool/software: Hi TI Experts, Could you provide S-parameter and IBIS model of IO-buffer for performing simulations

  • [FAQ] TDA4VM: VPAC LDC configuration for image flipping (TDA4x/AM6xA)

    Part Number: TDA4VM Tool/software: How can I flip images using LDC?

  • [FAQ] AM625: PCB Pattern Recommendations for Specific Peripherals

    Part Number: AM625 Tool/software: Hi Team, My customer is creating their PCB and have a few questions. Is there any recommendations or recommended values (for interconnect length or CLK-to-DATA interconnect difference) for the peripherals below…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP Custom board hardware design – JTAG Pulldown/Pullup

    Part Number: AM625 Tool/software: Hi Team, My customer has questions about JTAG pulldown/pullup. Regarding the TCK, TDI, TMS signals, is pullup required? It does not seem to be mentioned in the datasheet and says in the link below that it depends…

  • [FAQ] J784S4XEVM: How to load TIFS using JTAG on HS-FS device?

    Part Number: J784S4XEVM Tool/software: How to load TIFS using JTAG on HS-FS device?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: Custom board hardware design - SD card (MMC1) VDD power supply

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62-LP Tool/software: Hi, My customer is using SD card boot only for development phase. For production, only QSPI boot is used. QSPI or SD card boot selection is done by DIP switch on the board…

  • [FAQ] AM644x: Pin Attributes in excel

    Part Number: AM62A7-Q1 Other Parts Discussed in Thread: AM6442 Tool/software: Can you supply the pin list of the AM6442 in excel format? Thanks

  • [FAQ] AM62A7: How to stream video from AM62x devices over Wi-Fi using CC33XX

    Part Number: AM62A7 Other Parts Discussed in Thread: CC3301 , AM62P , AM625 , AM620-Q1 , AM625-Q1 , AM62P-Q1 , AM62A3 , , AM67A , CC3351 , CC3350 , AM623 , CC3300 , SK-AM62B , SK-AM62A-LP , SK-AM62P-LP , BEAGLEY-AI , M2-CC3351 Tool/software: I saw…

  • [FAQ] AM62A7: Bad Block Implementation for NAND Flash Parts

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG Tool/software: From release 10.00.00.14 onwards, BBM has been implemented in TI Drivers for NAND Flash Parts. AM62A MCU SDK: https://www.ti.com/tool/download/MCU-PLUS-SDK-AM62A/10.00…

  • [FAQ] TPS62867: TPS62867RQYR head room

    Part Number: TPS62867 Tool/software: Hi Experts, Customer is using the below device The input is 3.6V - 5% The output is 3.3V + 5% Current 1-2 A. Is there a min voltage difference that is required between the output and the input. Regards…

View FAQ threads
  • Threads 197925 Discussions