Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DP83822I: Does Oscillator Clock or other external clock source to XI pin need to be stable before PHY power?

    Part Number: DP83822I Tool/software: Yes, Clock in external clock mode shall be available at power ramp. If not available, it is recommended to hold RESET_N low and release it at least 100 us aer external clock is stable.

  • [FAQ] What is the "VILC" Electrical Spec in I2C Buffers?

    Other Parts Discussed in Thread: TCA9517A Part Numbers: TCA9517A , TCA9517 , TCA9509 FAQ: Logic and Voltage Translation > IxC >> What is the "VILC" Electrical Spec in I2C Buffers ? VILC = Input LOW Contention Voltage VILC is the internal voltage…

  • [FAQ] What is a buffered LOW?

    Part Number: TCA9517 Other Parts Discussed in Thread: TCA9617B FAQ: Logic and Voltage Transla tion > IxC >> What is a buffered LOW ? A "buffered LOW" is the output voltage of the buffer when a low voltage input (VIL) is present on the input. This…

  • [FAQ] SN65DSI8x Programming Tools

    Part Number: SN65DSI84 Other Parts Discussed in Thread: SN65DSI85 , SN65DSI83 , SN65DSI86 Tool/software: DSI Tuner Tool (SN65DSI83, SN65DSI84, SN65DSI85): This tool is used to translate the video timings of the LVDS panel bein used to register values…

  • [FAQ] TUSB211A: How does a USB2 redriver boost the signal that passes through it?

    Part Number: TUSB211A Tool/software: How does a USB2 redrivers boost the signals that come through it? I do not understand how this is possible since some redrivers do not need to be directly incorporated into the trace to process and boost the signal…

  • [FAQ] TUSB211A: Why do some USB2 redrivers not need to be directly integrated?

    Part Number: TUSB211A Other Parts Discussed in Thread: TUSB217A , TUSB214 , TUSB211 , TUSB216 , TUSB212 Tool/software: Some USB2 redrivers do not need to be directly integrated into a trace, and can just be placed over the trace. Why is that? Won't this…

  • [FAQ] DS280DF810EVM: How to reflash USB2ANY for use with SigCon Architect GUI

    Part Number: DS280DF810EVM Other Parts Discussed in Thread: USB2ANY Tool/software: In this FAQ, I will explain how to reflash a USB2ANY device to interface between an EVM board and SigCon Architect GUI. This FAQ applies to any EVM which is controlled…

  • [FAQ] DS125DF111: How to capture a full eye opening measurement using SMBus registers

    Part Number: DS125DF111 Other Parts Discussed in Thread: DS110DF111 , , DS100DF410 , DS110DF410 , DS125DF410 Tool/software: In this FAQ, I will cover the SMBus register sequence to capture a full eye opening measurement. This FAQ applies to the following…

  • [FAQ] DS320PR810: Using EyeScan to Optimize CTLE Setting on Your PCIe Redriver

    Part Number: DS320PR810 Tool/software: Hi All, Texas Instruments uses PCIe redrivers to perform signal conditioning on medium to upper medium loss systems. The redriver is effective in a wide variety of systems with losses ranging from -36dB to -56dB…

  • [FAQ] DP++ & Dual Mode Implementation using a DP redriver

    Part Number: TDP2004 Tool/software: What is Dual Mode Dual mode or DP++ allows for a DP source to output a HDMI signal to a sink without using an active protocol converter. The DP source must be DP++ capable for dual mode operation. The key considerations…

View FAQ threads