Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DP83TC811S-Q1: Why is Slave/Managed mode PHY linking up with Master/Autonomous PHY link partner?

    Part Number: DP83TC811S-Q1 Other Parts Discussed in Thread: DP83TC811R-Q1 When using DP83TC811S-Q1 (or DP83TC811R-Q1), and setting the PHY into managed mode as a slave device via bootstrapping settings, if this device is connected to a master link partner…

  • [FAQ] DS90UH949-Q1: Disable HDCP to work with UB Deserializer

    Part Number: DS90UH949-Q1 Hello, My customer would like to use DS90 UH949 -Q1 devices in place of the DS90 UB949A -Q1 to keep production running. In reviewing the details they have the following questions. Can the HDCP function be disabled? If so, how is…

  • [FAQ] Why am I getting "clause-45 not supported" and "error-95" errors with PHY drivers?

    Possible reason can be : - "phy_read_mmd" and "phy_write_mmd" are not supported in your kernel version (if version is old). Possible solution to be evaluated : - Change "phy_write_mmd" to "phy_write_mmd_indirect" function and do the…

  • [FAQ] DS90UB960-Q1: BIST Duration

    Part Number: DS90UB960-Q1 Hi Team, What is the recommended duration to run the BIST? Thanks Reed

  • [FAQ] How to select correct RGMII delay mode for PHY and MAC?

    RGMII standard asks for the introduction of delay in the clock (RX_CLK/TX_CLK) with respect to the respective data (RX_D*/RX_CTRL or TX_D*/TX_CTRL). This delay can be introduced at the source of the clock or at the receiver side. Following table should…

  • [FAQ] How to select the crystal's ppm specification for an Ethernet system?

    Other Parts Discussed in Thread: DP83TC811 Ethernet data travels effectively from one MAC to another MAC with two Ethernet PHYs in between. Each of these 4 ICs can have their own reference clocks and crystal attached to each is the usual source of this…

  • [FAQ] DP83867IR: DP83867 digital loopback fail, how to set MII and PCS loopback

    Part Number: DP83867IR Hi Team: Customer side need our help to find the root cause of DP83867 Communication failure issue from one failed board . could you please help to take a look at the attached , customer need to know How to enable MII and PCS…

  • [FAQ] DS90UB933-Q1: DS90UB933-Q1 and DS90UB913A-Q1 MODE Decode

    Part Number: DS90UB933-Q1 Other Parts Discussed in Thread: DS90UB913A-Q1 , How do I determine if the DS90UB933-Q1 or DS90UB913A-Q1 device is operating in RAW10, RAW12LF, or RAW12HF through registers?

  • [FAQ] Demystifying Surge Protection

    Please refer to the links below to access our content related to Demystifying Surge Protection: Videos https://training.ti.com/getting-started-interface-protection White paper https://www.ti.com/lit/pdf/slyy152

  • [FAQ] ESD Fundamentals Training

    Please refer to the links below to access our ESD Fundamentals training: Videos https://training.ti.com/getting-started-interface-protection Blog Posts Part 1: https://e2e.ti.com/blogs_/b/powerhouse/posts/esd-fundamentals-part-1-what-is-esd-prote…

View FAQ threads