• Threads 52590 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM263P4: How to block ethernet packets with a particular unicast address?

    Part Number: AM263P4 Ethernet packets can be blocked or forwarded based on their packet addresses. Unicast address is a specific type of address that is intended for one to one communication. ALE in CPSW susbystem can be configured to drop packets…

  • [FAQ] AM2634-Q1: How can I persist a data structure from my code in flash storage on an AM263 microcontroller?

    Part Number: AM2634-Q1 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH This FAQ highlights how you make a datastructure to be stored in flash in AM263 microcontroller. Typically we can do this in AM263Px and AM261x microcontroller where XIP…

  • [FAQ] AM263P4-Q1: How to flash/program custom external flashes

    Part Number: AM263P4-Q1 Other Parts Discussed in Thread: UNIFLASH This FAQ explains how to setup the flash utility to flash into external flashes which are not supported out of the box. The method mentioned in this FAQ would be the same for AM261 and…

  • [FAQ] MSPM0-SDK: Software and Evaluation Board Design Resources for Application note of Single Phase AC Shunt Power Monitor with Low Cost MSPM0

    Part Number: MSPM0-SDK This thread is used to update the software or hardware update for application note of Single Phase AC Power Monitor with MSPM0 Hardware_Software.zip

  • [FAQ] AM263P4-Q1: Last 24 bytes of Bank0, Bank1 in OCRAM are no longer visible

    Part Number: AM263P4-Q1 Hi, Regarding the E2E mentioned below, could you please provide us with further information? We are currently using SDK 9.2, and due to our development schedule, we do not have sufficient time to migrate to SDK 11.0. Could you…

  • [FAQ] printf demo for MSPM0 device

    Other Parts Discussed in Thread: LP-MSPM0G3507 printf_to_uart_LP_MSPM0G3507_nortos_ticlang.zip Default UART pin is PA10 and PA11, and it's based on LP-MSPM0G3507 default. Please check corresponding Launchpad's User guide schematic before test. There…

  • [FAQ] AM2612-Q1: How to debug XIP application using CCS Theia

    Part Number: AM2612-Q1 Hi Experts, Please share the steps to debug XIP applications using CCS Theia.

  • [FAQ] MSPM0: Software demo for OPT3001 and TMP116

    Part Number: MSPM0G3507 Other Parts Discussed in Thread: OPT3001 , TMP116 This is a software resource about MSPM0 communicating with OPT3001 and TMP116 on BASSENSORS. Drive_BASSENSORS.zip

  • [FAQ] AM263P4: AM263Px: Facing issues with Ethernet MAC PORT IOCTL API.

    Part Number: AM263P4 Hi team, I am using the MCU_PLUS_SDK AM263Px version v11.0 and I am facing issues running ethernet examples. From the logs I suspect issues with MAC Port IOCTL calls. This is causing example failure, failures to read PHY registers…

  • [FAQ]: AM26x: How to enable CPTS packet timestamping in CPSW

    Part Number: AM2612 Hi experts, Can you please provide the steps to enable Packet time-stamping in CPSW. What changes do I need in my application code and syscfg to enable the hardware time-stamping. Can you provide sample code snippets for the same…

View FAQ threads