Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How to Setup IBV icECAT EtherCAT Master Stack on TI Processors?

    Part Number: AM6442 Other Parts Discussed in Thread: LP-AM243 , TMDS64EVM Tool/software: icECAT is a 3rd party EtherCAT Master stack developed by IBV . To obtain the software stack for evaluation please send a request by selecting the "Send Request…

  • [FAQ] How to Setup an EtherCAT Network using TI Processors

    Part Number: AM6442 Tool/software: TI processors have the capability to run as an EtherCAT MainDevice to control EtherCAT SubDevices such Beckhoff I/O terminals or an AM243x running an EtherCAT subdevice example . This is enabled by using a 3rd…

  • [FAQ] TDA4VH-Q1 and TDA4VL-Q1: Errata i2437 - Streaming Engine (SE) Clock-Gating Turning Off Too Early: Background and Workaround

    Part Number: TDA4VH-Q1 Tool/software: Background Errata ID: i2437 refers to the C7x Streaming Engine (SE). This errata applies to J721S2 and J784S4 and the details can be found in their respective Processor Silicon Revision documents. Note that…

  • [FAQ]:Migration Tips for Developers Transitioning to MPU Devices from Old Microcontroller.

    Part Number: AM6442 Other Parts Discussed in Thread: AM62P Tool/software: With this FAQ, developers can ensure a smoother, faster transition to Sitara MPU devices (AM64x,AM243,AM62x,AM62A,AM62P and AM62D) and maximizing the benefits of the new architecture…

  • [FAQ] AM62A7-Q1: Balena etcher flash error workaround

    Part Number: AM62A7-Q1 Tool/software: Hi all, Due to the latest version(V1.19.x) Balena etcher have some bugs will cause flash error report. regarding this error, pls use old version Balena tool to work around. below is the download link for V1.7.x…

  • [FAQ] How to flash eMMC with Lauterbach JTAG on AM62x

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62A-LP , SK-AM62 , SK-AM62-LP Tool/software: AM62x boot rom supports booting from eMMC. Please refer to AM62x TRM "5.4.4 eMMC Boot" for details on eMMC boot support by boot rom. The FAQ lists…

  • [FAQ] How to flash GPMC-NAND with Lauterbach JTAG on AM62x

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62-LP Tool/software: AM62x boot rom supports booting from parallel GPMC NAND. From "5.4.9.1 GPMC NAND Bootloader Operation" in AM62x TRM "GPMC NAND boot only supports boot from ONFI 1.0 compatible…

  • [FAQ] PROCESSOR-SDK-AM64X: How to generate GPIO interrupt on both falling and rising edge?

    Part Number: PROCESSOR-SDK-AM64X Tool/software: How to configure GPIO interrupt for both rising and falling edge? How to identify which edge (i.e. rising or falling) generates interrupt?

  • [FAQ] AM6442: PCIe clock architecture

    Part Number: AM6442 Tool/software: HI Should we understand that COMMON CLOCK ARCHITECTURE is mandatory (therefore external source also is) whatever the clock being spread spectrum or not ? with best regards Bruno

  • [FAQ] : AM6X Device Reset Troubleshooting Document

    Part Number: AM6442 Tool/software: Many users are asking how to investigate the Reset source when the device continuously getting resting. The below FAQ brief can be helpful to find the Reset reason . The FAQ mainly focuses on AM64X devices, but…

View FAQ threads
  • Threads 198401 Discussions