Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] SK-AM62B-P1: How to implement encrypted filesystems using dm-crypt and initramfs

    Part Number: SK-AM62B-P1 Tool/software: Hello all, This is a detailed guide on implementing an encrypted filesystem on an SK-AM62B-P1 using dm-crypt. Please note that similar steps with minimal changes should also work on other targets based on…

  • [FAQ] TMUX1308-Q1: EN and Control inputs termination - AM62P, AM62A use case

    Part Number: TMUX1308-Q1 Other Parts Discussed in Thread: TMUX1308 , AM625 , TMUX1308A , SN74LV4051A , TMUX1308A-Q1 , ADC121S101 , , TPS65224-Q1 Tool/software: Hi Team, TMUX1308 EN and control A0..A2 is being controlled by AM625 Sitara SOC. …

  • [FAQ] TMS320C6657: How to re-build the Nor writer code of processor SDK 6.3 ?

    Part Number: TMS320C6657 Tool/software: How to re-build the Nor writer code of processor SDK 6.3 ?

  • [FAQ] AM62A7: Could you help to provide Pinmux excel file for AM62A

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi Expert, Could you help to provide Pinmux excel file for AM62A? SysConfig Tool export csv file does not list MUX Mode. TDAV4VM provides MUX Mode Thanks …

  • [FAQ] AM6412: VDDSHV5 connections if not using MMC1

    Part Number: AM6412 Tool/software: Hi, In our design we're connecting an eMMC to MMC0 and not using MMC1. Table 6-80 (of TRM) says: VDDA_3P3_SDIO, CAP_VDDSHV_MMC1: If SDIO_LDO is not used to power VDDSHV5, each of these balls must be…

  • [FAQ] AM623: Could you help to provide Pinmux excel file for AX62XX?

    Part Number: AM623 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi Expert, Could you help to provide Pinmux excel file for AX62XX? SysConfig Tool export csv file does not list MUX Mode. TDAV4VM provides MUX Mode Thanks …

  • [FAQ] PROCESSOR-SDK-AM64X: Integration of custom PHY using MCUSDK

    Part Number: PROCESSOR-SDK-AM64X Tool/software: Hi, I am designing my custom board using AM64x/AM243x + MCUSDK. But not using PHY provided on EVM/LP board. Can you provide guidance how to do this? Regards

  • [FAQ] : How to trigger DMA with the help of GPIO on AM64X/AM243 and AM62X devices ?

    Part Number: AM6412 Tool/software: Hello Users, Many users are asking to trigger DMA with the help of GPIO on AM64X/AM243 and AM62X devices. So, I have created an example of this solution on AM64X and the procedure is the same for all other devices…

  • [FAQ] PROCESSOR-SDK-AM64X: How to create a PWM using a timer

    Part Number: PROCESSOR-SDK-AM64X Tool/software: Hi, can we use a timer to generate a PWM? If so, how could we control/change its frequency and duty cycle while running?

  • [FAQ] AM623: Power-Up Sequencing for VPP?

    Part Number: AM623 Tool/software: Hi Expert, Power-Up Sequencing refers to the datasheet to set up, but now I have a question about the power-up timing of the VPP voltage. And the Figure 7-5. Power-Up Sequencing graphic shows Hi-Z. I don’t quite…

View FAQ threads
  • Threads 198153 Discussions