Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VM: How to move to Native Linux Driver on SDK 8.4 for J7 and DRA8 Devices

    Part Number: TDA4VM Other Parts Discussed in Thread: DRA829 , , DRA821 , TDA4VH Hi I want to use the new Native Linux Driver introduces in PSDK Linux 8.4. How do I start?

  • [FAQ] TDA4VM: Starting openVX application automatically at Linux boot

    Part Number: TDA4VM Can we start running an OpenVX application automatically at Linux Boot

  • [FAQ] AM625: How to enable DM firmware logs & TIFS firmware logs in Processor SDK Linux v8.4

    Part Number: AM625 Hello, I am using the AM62 SK eva kit with PROCESSOR-SDK-LINUX-AM62 08.04.01.03 As I understand MAIN_UART1 and WKUP_UART0 is used by the DM and TIFS firmware. This is the configuration MAIN_UART0: Used for Linux and U-Boot…

  • [FAQ] AM625: jtag schematics to implement in customer board

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62 Hi everybody , customer would like to have Jtag connections/capabilities on their production board . I suggested to copy SK-AM62 but here are questions : - do you need to implement…

  • [FAQ] AM625: Disturance on OSPI CLK connected to SPI NOR

    Part Number: AM625 We are facing problem when connecting a SPI Nor (W25Q128VEIQ) to OSPI CS0. Basically it is working but from time to time it comes to errors during SF PROBE command in u.boot. Please find attached the CLK Signal measured during…

  • [FAQ] AM62x: How to customize eMMC and OSPI flash layout for SPL/u-boot booting with TI AM62x Linux SDK

    Part Number: SK-AM62 I am attempting to boot the AM62x SK EVM from eMMC and OSPI. The board I have is revision PROC114E1. I am using the TI provided SD-Card image located here: https://dr-download.ti.com/software-development/software-development…

  • [FAQ] AM6412: Passing USB compliance test patterns trhough a USB 2.0 hub

    Part Number: AM6412 Hi TI, I can generate USB compliance test patterns on AM64 SoC by the following command # devmem2 0x0f410480 w 0xA0 # devmem2 0x0f410080 w 0x4 # devmem2 0x0f410484 w 0x40000000 However, the test pattern stops transferring…

  • [FAQ] AM6412: USB compliance test pattern generation

    Part Number: AM6412 Hi TI, How to generate USB compliance test from CPU In Linux kernel 5.10 on AM64xx. I followed the instructions below. TDA4VM: USB 2.0 host test mode Set dr_mode to host. # cat /proc/device-tree/bus\@f4000/cdns-usb…

  • [FAQ] SK-AM62: how to disable the HMI demo

    Part Number: SK-AM62 Hello. i am working with linux arago default image for am62 evaluation board. I am trying to understand how reduce boot time, and get command prompt as fast as i can. Just to have an idea of how to speed up this, i would like…

  • [FAQ] TDA4VM: PDK Interrupt registration for R5F using OSAL

    Part Number: TDA4VM This document is intended to explain the interrupt registration process for R5F cores used in TI PDK

View FAQ threads
  • Threads 198104 Discussions