Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TDA4VH-Q1: How do I migrate from UFS 2.1 to UFS 3.0+ (3.1, 4.1, etc)?

    Part Number: TDA4VH-Q1 UFS 2.1 devices are growing more difficult to purchase, as UFS 2.1 was implemented in 2016. I have a UFS 3.0+ device, and I would like to replace the UFS 2.1 device in my design. How do I go about doing that? Are there any changes…

  • [FAQ] Bad Block management in AM64x ROM on GPMC-NAND booting

    Part Number: AM6442 Other Parts Discussed in Thread: TMDS64EVM AM64x boot ROM supports booting from parallel GPMC-NAND. From "4.4.10 GPMC NAND Boot" in AM64x TRM "AM64x ROM only supports boot from ONFI 1.0 compatible 8 bit parallel NAND memory up to…

  • [FAQ] AM2754-Q1: Implementing Firmware Update Over Ethernet (ENETFOTA) on AM275x

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: UNIFLASH , AUDIO-AM275-EVM The ENETFOTA example demonstrates how Ethernet can be used to transfer a new application image from a host PC to an AM275x device that is currently running an older application…

  • [FAQ] AM5728: How to configure and verify MMU settings in SYS/BIOS on AM57xx

    Part Number: AM5728 How can we modify and verify MMU configurations in the SYS/BIOS .cfg file?

  • [FAQ] AM2434: XIP (eXecute In Place) Mode Configuration with Default Serial Flash Parts

    Part Number: AM2434 While the existing OSPI driver implements XIP mode functionality, the default Flash parts (S28HS512T and S25HL512T) available on AM24x, AM64x, AM62x, and AM275x boards, do not support Read-While-Write (RWW) operations or multi-bank…

  • [FAQ] TDA4VL-Q1: ECC Self Test Procedure

    Part Number: TDA4VL-Q1 What is the effort required by the system integrator to enable and test ECC on the different IPs on the SoC using ECC aggregators?

  • [FAQ] TDA4VL-Q1: POK TRIM Value Setting

    Part Number: TDA4VL-Q1 Other Parts Discussed in Thread: TDA4VL What are the recommended POK TRIM value settings for each POK instance?

  • [FAQ] TDA4VH: Enable Falcon Boot Mode in J784S4

    Part Number: TDA4VH How to enable falcon boot on J784S4 11.02 Linux SDK ? Boot Flow: R5 SPL -> ATF -> OPTEE -> Kernel Regards Gokul

  • [FAQ] TDA4VL-Q1: POK Untrimmed Bandgap Configuration Issue

    Part Number: TDA4VL-Q1 POK (Power OK) undervoltage detection fails during software diagnostic testing in the bootloader, causing boot failures in approximately 1-3% of devices. The POK diagnostic module fails to detect undervoltage events even when…

  • [FAQ] PRU Arbitration Delay

    I am writing a PRU application for a PRU-ICSS device (AM261x, AM263Px, AM263x, AM335x, AM437x, AM57x)**, PRUSS device (AM62x), or a PRU_ICSSG device (AM24x, AM64x, AM65x). Arbitration delay can add additional clock cycles to a PRU read or write command…

View FAQ threads
  • Threads 202316 Discussions