Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How to enable switching capability between GPO and GPI operation for PRU GPIO?

    Part Number: AM6442 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Each PRU_ICSSG PRU processor implements fast GPO through its R30 register and fast GPI through R31 register. AM64x/AM243x has 20 pinned out PRU GPIO pins and the device…

  • [FAQ] AM625: ETH1_LED_100 and ETH1_LED_ACT dose not work

    Part Number: AM625 Tool/software: Hello IT Expert Our custom board uses the same reference design of Ethernet/LED HW as in attached custom board schematic. 1. There is no signal (100%) for CPSW_ETH1_LED_ACT (even we make network traffic by ping…

  • [FAQ] AM3351 , AM3352 , AM3354 , AM3356 , AM3357 , AM3358 , AM3359 Custom board design – E2E and FAQ references to Get started

    Part Number: AM3352 Other Parts Discussed in Thread: AM3358 , AM3354 , AM3359 , , AM3356 , SYSCONFIG Tool/software: Hi TI Experts, Can you provide a List of E2Es that can be referred when starting a custom board hardware design?

  • [FAQ] How to read SOC_UID from OPTEE on AM6x SoC

    Part Number: AM625 Tool/software: SOC_UID is a device specific identifier calculated by ROM based on "KEK of the device which is unique to every single device, plus other ROM mata-data structure". - unique per SoC and persistent - available on HS…

  • [FAQ] AM625: DVH Trace Length Matching Requirements

    Part Number: AM625 Tool/software: Hi, I'm designing a DVH to be laid out by SVT and am working on the layout guidelines for them. I am trying to find the trace length matching requirements for certain components but can't seem to find them on any…

  • [FAQ] SK-AM62B-P1: How to implement encrypted filesystems using dm-crypt and initramfs

    Part Number: SK-AM62B-P1 Tool/software: Hello all, This is a detailed guide on implementing an encrypted filesystem on an SK-AM62B-P1 using dm-crypt. Please note that similar steps with minimal changes should also work on other targets based on…

  • [FAQ] TMUX1308-Q1: EN and Control inputs termination - AM62P, AM62A use case

    Part Number: TMUX1308-Q1 Other Parts Discussed in Thread: TMUX1308 , AM625 , TMUX1308A , SN74LV4051A , TMUX1308A-Q1 , ADC121S101 , , TPS65224-Q1 Tool/software: Hi Team, TMUX1308 EN and control A0..A2 is being controlled by AM625 Sitara SOC. …

  • [FAQ] TMS320C6657: How to re-build the Nor writer code of processor SDK 6.3 ?

    Part Number: TMS320C6657 Tool/software: How to re-build the Nor writer code of processor SDK 6.3 ?

  • [FAQ] AM62A7: Could you help to provide Pinmux excel file for AM62A

    Part Number: AM62A7 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi Expert, Could you help to provide Pinmux excel file for AM62A? SysConfig Tool export csv file does not list MUX Mode. TDAV4VM provides MUX Mode Thanks …

  • [FAQ] AM6412: VDDSHV5 connections if not using MMC1

    Part Number: AM6412 Tool/software: Hi, In our design we're connecting an eMMC to MMC0 and not using MMC1. Table 6-80 (of TRM) says: VDDA_3P3_SDIO, CAP_VDDSHV_MMC1: If SDIO_LDO is not used to power VDDSHV5, each of these balls must be…

View FAQ threads
  • Threads 198421 Discussions