Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM62A7 / AM62A7-Q1 / AM62A3 / AM62A3-Q1 / AM62A1-Q1 / AM62D-Q1: Custom Board Hardware design - IBIS Model Inquiry

    Part Number: AM62A1-Q1 Other Parts Discussed in Thread: AM62A3 , AM62A7 Tool/software: Hi Team, Hope you're doing well. Could you share the IBIS model of AM62A12AQMSIAMBRQ1 under different temp?(-40oC/25oC/85oC) Thank you.

  • [FAQ] AM64x (AM6442, AM6441, AM6422, AM6421, AM6412, AM6411) and AM234x (AM2434, AM2432, AM2431 - ALV): Custom board hardware design - SK and EVM EXT_REFCLK1 CLKOUT0 use case and configuration

    Part Number: AM6422 Other Parts Discussed in Thread: SK-AM64B , , CDCLVC1310 Tool/software: Hi, In AM6422 evaluation board SK-AM64B. It connect the EXT_REFCLK1 to CLKOUT0 signal. i have some question about it. 1. EXT_REFCLK1 is 3.3V. Why it connect…

  • [FAQ] PROCESSOR-SDK-AM64X: I2C Integration Guide

    Part Number: PROCESSOR-SDK-AM64X Other Parts Discussed in Thread: SYSCONFIG Tool/software: On Sitara Family of Processors, there are multiple instances of I2C present. Some of the I2C instances are available in the MAIN Domain[example: SoC_I2C0…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62A / AM62D-Q1 / AM62P Custom board hardware design – Partial IO LPM support

    Part Number: AM625 Tool/software: Hi TI Experts, Could you guide me on testing Partial IO LPM using the SK for UART or USB

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP / AM62A7 / AM62A3 / AM62A1-Q1 / AM62D-Q1 / AM62L / AM62P / AM62P-Q1 / AM64x / AM243x Custom board hardware design – S-parameter and IBIS model of IO-buffer

    Part Number: AM625 Other Parts Discussed in Thread: AM62P , Tool/software: Hi TI Experts, Could you provide S-parameter and IBIS model of IO-buffer for performing simulations

  • [FAQ] TDA4VM: VPAC LDC configuration for image flipping (TDA4x/AM6xA)

    Part Number: TDA4VM Tool/software: How can I flip images using LDC?

  • [FAQ] AM625: PCB Pattern Recommendations for Specific Peripherals

    Part Number: AM625 Tool/software: Hi Team, My customer is creating their PCB and have a few questions. Is there any recommendations or recommended values (for interconnect length or CLK-to-DATA interconnect difference) for the peripherals below…

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP Custom board hardware design – JTAG Pulldown/Pullup

    Part Number: AM625 Tool/software: Hi Team, My customer has questions about JTAG pulldown/pullup. Regarding the TCK, TDI, TMS signals, is pullup required? It does not seem to be mentioned in the datasheet and says in the link below that it depends…

  • [FAQ] J784S4XEVM: How to load TIFS using JTAG on HS-FS device?

    Part Number: J784S4XEVM Tool/software: How to load TIFS using JTAG on HS-FS device?

  • [FAQ] AM625 / AM623 / AM620-Q1 / AM625-Q1 / AM625SIP: Custom board hardware design - SD card (MMC1) VDD power supply

    Part Number: AM625 Other Parts Discussed in Thread: SK-AM62-LP Tool/software: Hi, My customer is using SD card boot only for development phase. For production, only QSPI boot is used. QSPI or SD card boot selection is done by DIP switch on the board…

View FAQ threads
  • Threads 198112 Discussions