Texas Instruments (TI) Amplifiers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search amplifier IC content or ask technical support questions on everything from precision and general purpose operational amplifiers (op amps) to instrumentation and differential amplifiers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] Does TI have a gain and offset error excel calculator for isolated voltage sensing?

    Other Parts Discussed in Thread: AMC1301-Q1 Hi, Does TI have a gain and offset error excel calculator for isolated voltage sensing?

  • [FAQ] LM358LV: What is the difference between the LM358, LM358B, and LM358LV op amp replacements?

    Part Number: LM358LV Other Parts Discussed in Thread: LM358B , LM358-N , , LM358 , LM324 , LM321LV , LM324LV , LM321 Hello, When searching for an LM358 I found a bunch of different versions, LM358, LM358-N, LM358B, and LM358LV. What's the difference…

  • [FAQ] How do I design Low Noise & Low Distortion Headphone & Small Signal Audio Amplifiers?

    Other Parts Discussed in Thread: LM833 How do I design Low Noise & Low Distortion Headphone & Small Signal Audio Amplifiers? Headphone Amplifiers On-Chip Thin Film Resistors Enable High-Performance Audio Circuitry – SBOA312 Stabilizing Difference…

  • [FAQ] LMV358: What is the best cross reference replacements for the LMV321, LMV358, LMV324 op amp devices?

    Part Number: LMV358 Other Parts Discussed in Thread: LMV321 , , LMV324 , , LMV324A , LMV321A , TLV9002 , TLV9004 , TLV9001 , LM2902 , LM2904 , LM2904-Q1 , LM358B , LM358LV , LM358 , LM2904B , LM2904LV , LM2902LV , LM2904B-Q1 , OPA2990 , TLV9064 , TLV9062…

  • [FAQ] ISO224: Tying ISO224 OUTN to GND2

    Part Number: ISO224 Other Parts Discussed in Thread: , TLV6001 , OPA277 This might be a silly question, but is there any problem that might arise when tying the negative output of ISO224 to the low-side ground, GND2? My original plan was to do this…

  • [FAQ] How do I make an op amp circuit stable?

    Other Parts Discussed in Thread: 4213 The attached presentation details how to make many common op amp circuits stable. 4213.Solving Op Amp Stability 2015_TG.pptx

  • [FAQ] What are the best cross reference replacement for the MCP6001, MCP6002, and MCP6004 devices?

    Other Parts Discussed in Thread: TLV9064 , TLV9004 , TLV9001 , TLV9062 , TLV9061 , TLV9002 Hello, I need to identify replacement op amps for the MCP6001, MCP6002, and MCP6004 devices. What are the best replacement amplifiers from TI? Thanks!

  • [FAQ] LM2904: What are the best op amps for low cost designs?

    Part Number: LM2904 Hello, Could you help with the selection of op amps for low cost or cost-optimized circuit designs? Thanks!

  • [FAQ] Can you tell me the number of transistors in my device for my reliability modeling?

    Sometimes it is useful to know the number of transistors in a part for quality and reliability modeling. How can I get that information from TI?

  • [FAQ] Things to consider with high voltage measurements with op-amps?

    Other Parts Discussed in Thread: ANALOG-ENGINEER-CALC , TLV313 If your circuit has a high voltage measurement circuit, there are many things to consider. Have you considered the effects of temperature? The voltage coffiecient of the resistors?

View FAQ threads