Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS280DF810EVM: How to reflash USB2ANY for use with SigCon Architect GUI

    Part Number: DS280DF810EVM Other Parts Discussed in Thread: USB2ANY Tool/software: In this FAQ, I will explain how to reflash a USB2ANY device to interface between an EVM board and SigCon Architect GUI. This FAQ applies to any EVM which is controlled…

  • [FAQ] DS125DF111: How to capture a full eye opening measurement using SMBus registers

    Part Number: DS125DF111 Other Parts Discussed in Thread: DS110DF111 , , DS100DF410 , DS110DF410 , DS125DF410 Tool/software: In this FAQ, I will cover the SMBus register sequence to capture a full eye opening measurement. This FAQ applies to the following…

  • [FAQ] DS320PR810: Using EyeScan to Optimize CTLE Setting on Your PCIe Redriver

    Part Number: DS320PR810 Tool/software: Hi All, Texas Instruments uses PCIe redrivers to perform signal conditioning on medium to upper medium loss systems. The redriver is effective in a wide variety of systems with losses ranging from -36dB to -56dB…

  • [FAQ] DP++ & Dual Mode Implementation using a DP redriver

    Part Number: TDP2004 Tool/software: What is Dual Mode Dual mode or DP++ allows for a DP source to output a HDMI signal to a sink without using an active protocol converter. The DP source must be DP++ capable for dual mode operation. The key considerations…

  • [FAQ] DS320PR810: How should PCIe redriver PD pins be configured?

    Part Number: DS320PR810 Tool/software: TI PCIe Gen 5/Gen 4 redrivers have powerdown (PD or PWDN) pins. How should I configure them, and why does TI suggest connecting them to inverted PERST# or PRSNT#?

  • [FAQ] SN65DPHY440SS: What is the design constraint for DPHY440 lane 0 when using in a MIPI CSI design?

    Part Number: SN65DPHY440SS Other Parts Discussed in Thread: SN75DPHY440SS Tool/software: I'm utilizing the SN75DPHY440SS in 4 lane configuration with default configuration parameters, sourced by a CSI-2 source. Lanes 1, 2, and 3 are correctly driven…

  • [FAQ] TUSB1142: How to properly connect the TUSB1142 FLIP pin to the TPS2583xA-Q1 CC controller

    Part Number: TUSB1142 Other Parts Discussed in Thread: TPS25820 , Tool/software: The TUSB1142 design uses the Flip signal from a TPS25820 to switch the SuperSpeed signals from a USB Type C connector. We are not able to get SuperSpeed to work at all.

  • [FAQ] DS280DF810: Why is 25G/28G Retimer PRBS Generator Not Working?

    Part Number: DS280DF810 Other Parts Discussed in Thread: DS250DF410 Tool/software: Introduction: One common debug question when using TI's 25G/28G is why is the PRBS generator not working? This FAQ will review the key criteria for the retimer PRBS…

  • [FAQ] TUSB211A: Why does the USB 2.0 redriver not appear to work when taking eye-diagrams?

    Part Number: TUSB211A Tool/software: In order to perform eye-diagram testing, the TUSB211A and other USB 2.0 redrivers must first detect the scope termination after power on or reset. Once termination has been detected, then the redriver will enable…

  • [FAQ] DS280DF810: Which 25/28G Retimer Should I Select?

    Part Number: DS280DF810 Other Parts Discussed in Thread: DS250DF210 , DS250DF230 , DS250DF410 , DS250DF810 , Tool/software: TI has several retimers in its 25/28G retimer product family. This FAQ breaks down some of the key differences between TI's 25/28G…

View FAQ threads