Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS90UB913A-Q1: Does UB913 support BT 601 format with UB964?

    Part Number: DS90UB913A-Q1 Hi Team My customer is considering to use 913 and 964. they want to know if 913/964 can support BT 601 format 1280x720@30fps with YUV 422 8bit. I think it is not a problem but I want to check with team 1more time for sure…

  • [FAQ] DS90UB947-Q1: Does device enable OLDI port input even Link detect status (0x0c bit[0]=1b'0 ) is low??

    Part Number: DS90UB947-Q1 Hi Team My customer is developing 947 <->948 for CID application. now they met some issue that when they test 947 with their tester display module with 948, 0x0c bit[0] is high and display is OK. but when they test 947…

  • [FAQ] DS90UB947-Q1: Tolerance of Target voltage for MODE_SEL

    Part Number: DS90UB947-Q1 Hi Team My Customer is asking how much tolerance 947device has for Mode_sel. now my customer wants to set #5 for mode_sel1 but they only has 82Kohm PU/100Kohm PD. so ratio would be 0.549. but recommended ratio is 0.560…

  • [FAQ] TUSB1064: How do I debug DP Alt Mode over USB Type-C interface?

    Other Parts Discussed in Thread: TUSB546A-DCI , TUSB564 , TUSB1064 , TUSB1046A-DCI , TUSB1146 , TS3USBCA4 How do I debug DP Alt Mode issue over the USB Type-C interface?

  • [FAQ] TPS65988: Example project to share power between Type-C PD source ports dynamically without using EC.

    Part Number: TPS65988 This example project has been developed to help designers who are working on dual port applications such as smart plugs, multi-port adapters, avionics seat backs, wall-sockets... which often require dynamic power sharing between…

  • [FAQ] TUSB9261: Where can I get the VIF file for the TUSB9261

    Part Number: TUSB9261 Where can I get the latest VIF file for the TUSB9261 KGD for USB-IF Compliance Testing?

  • [FAQ] TUSB8041: What are the power-up and reset timing requirements for the USB hub?

    Part Number: TUSB8041 Other Parts Discussed in Thread: TUSB8044A , , TUSB8044 , TUSB8042A , TUSB8043 , TUSB8020B , TUSB8043A , TUSB8042 When using the TUSB8041, does it matter which power supply ramps first and how does it impact power on reset timing…

  • [FAQ] SN65DSI84: How to debug flickering video with SN65DSI83, SN65DSI84, and SN65DSI85

    Part Number: SN65DSI84 Other Parts Discussed in Thread: DSI-TUNER The video on my display panel is flickering when I use these devices. How do I debug this issue?

  • [FAQ] DP83TD510E: Does my DP83TD510E need to be initialized to establish link?

    Part Number: DP83TD510E Other Parts Discussed in Thread: MSP430F5529 FAQ – Does my DP83TD510E need to be initialized to establish link? The DP83TD510E is a 10Base-T1L PHY that can link between devices up to over 2km of SPE cable. TI’s preproduction…

  • [FAQ] TPS25750: How do I create a Sink-Only USB-C PD port to replace a legacy Barrel Jack Connector?

    Part Number: TPS25750 I want to replace a Barrel Jack connector with a USB-C PD port. The USB-C PD port only needs to Sink power. How can I optimize the schematic with the TPS25750 to achieve this functionality?

View FAQ threads