Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS90UH941AS-Q1: How to configure FPD-Link III 94x audio

    Part Number: DS90UH941AS-Q1 How do I configure audio for FPD-Link III 94x devices?

  • [FAQ] DP83826E: In enhanced mode, how does DP83826 strapping work?

    Part Number: DP83826E When configuring DP83826 in Enhanced Mode, please consult the following flowchart to understand how the different strap pins configure the PHY into various modes.

  • [FAQ] DP83TG720S-Q1: How to read or write registers in extended register space of Ethernet PHY?

    Part Number: DP83TG720S-Q1 write procedure for MMD "1F" registers: write reg<000D> = 0x001F write reg<000E> = <address> write reg<000D> = 0x401F write reg<000E> = <value> read procedure for MMD "1F" registers: write reg<000D> = 0x001F …

  • [FAQ] How can I ensure a successful PCIe Gen5 design?

    3 Tips for a successful PCIe Gen5 design With PCIe datarates increasing to 32Gbps in the latest PCIe Gen5 specification, PCIe has allowed for data higher throughput than ever before. Unfortunately, higher data rates can also mean more signal integrity…

  • [FAQ] DP83867CR: How to generate free-running 125MHz clock from DP83867?

    Part Number: DP83867CR To generate free running clock of 125MHz on the CLKOUT pin of DP83867 (synced with local reference clock on XI pin) : program register 0x0170[12:8] = 01000

  • [FAQ] DP83867CR: How to generate recovered clock using DP83867?

    Part Number: DP83867CR To generate clock in sync with the link-partner (recovered clock of 125MHz or 25MHz) on the CLKOUT pin of DP83867 : program register 0x0170[12:8] = 00000 for 125MHz program register 0x0170[12:8] = 00100 for 25MHz Note…

  • [FAQ] ESD and TVS Protection Devices: All Technical Documentation

    Application Notes Protecting Automotive Can Bus Systems from ESD Overvoltage Events ESD and Surge Protection for USB Interfaces Automotive SerDes ESD Protection MSP430 System-Level ESD Considerations (Rev. B)…

  • [FAQ] DP83TD510E: Can we use a transformer instead of Capacitor for AC coupling on the MDI side for DP83TD510?

    Part Number: DP83TD510E Yes, transformer can be used for filtering out the DC signal when the data is passing through the MDI side. In fact, we use transformer to filter out the AC signal in the Power over Data Line (PoDL) application. Here are the…

  • [FAQ] What is the difference between RMII slave signaling and RMII master signaling?

    RMII slave signaling is connecting 50MHz Crystal to two XI pin of the PHY and/or MAC RMII master signaling is connection 25MHz Crystal to one Master and provide a 50MHz reference lock through REF_CLK pin to the XI pin of the slave side. Slave side does…

  • [FAQ] DP83TC812R-Q1: How can I connect PHYs back to back over RMII?

    Part Number: DP83TC812R-Q1 There are two type of mode that RMII can support: RMII normal mode and RMII Repeater mode: RMII normal mode is also known as MAC to PHY RMII connection. This mode is set as default mode in DP83TC812 so it did not need…

View FAQ threads