• Threads 49389 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM2612: How to run Profinet Example on AM261x

    Part Number: AM2612 Other Parts Discussed in Thread: UNIFLASH Step-by-Step Guide to running profinet example on LP-AM261x. Requirements: 1. I ND COMMS SDK 2. CCS 3. Compiler 4. Syscfg 5. Uniflash GUI 6. Python and OpenSSL 7. LP-AM261x…

  • [FAQ] AM2612: "No Module Named Construct" on clean install / build of SDK example

    Part Number: AM2612 Hi ASM team, I get the following error after trying to build a simple GPIO toggle program on a clean install of the 10_02_00_15 SDK. Have we seen this before? All the best, Ethan Cope

  • [FAQ] MCU-PLUS-SDK-AM263X: SBL QSPI ENET missing python file "enet_uniflash.py"

    Part Number: MCU-PLUS-SDK-AM263X Other Parts Discussed in Thread: UNIFLASH Tool/software: Hi TI experts, I'm trying to run the sbl_qspi_enet application on AM263x. I see that the documentation ( software-dl.ti.com/.../EXAMPLES_DRIVERS_SBL_QSPI_ENET_AM263X…

  • [FAQ] MSPM0C1104: How to do factory reset with J-Link

    Part Number: MSPM0C1104 Tool/software: Here provide an script to do factory reset with J-Link, there is an readme file to show you how to do it. Important thing is remember to modify the device in open factory_reset.bat and connect the reset pin with…

  • [FAQ] LP-AM261: Resolving AM26x XDS110/JTAG issues: XDS110 / JTAG Debugger error: Unable to Access DAP (Error -1170), "Test Connection" Fails with SC_ERR_PATH_BROKEN

    Part Number: LP-AM261 Tool/software: Hi TI experts, I am using TI AM26x MCUs and trying to connect the board to my PC. When I try to connect to a CPU in CCS target configuration & debug window, I see the following error codes in the console: CS_DAP_0…

  • [FAQ] MSPM0L1306: BSL_GUI_EXE update

    Part Number: MSPM0L1306 Tool/software: This thread just for update the BSL_GUI_EXE. Due to some software release limitation, we can't put the MSPM0_BSL_GUI.exe file into our SDK < …\mspm0_sdk_xxxx\tools\bsl\BSL_GUI_EXE >. It need customer use the…

  • [FAQ] RM44L520: Building HALCoGen-generated code with Clang (Issues, successful workarounds, proposed upstream fixes)

    Part Number: RM44L520 Other Parts Discussed in Thread: HALCOGEN Tool/software: I have been using Clang/LLVM, specifically ARM's ATfE distribution , to compile HALCoGen-generated code. It mostly works great, but there are a few issues that have to…

  • [FAQ] AM263P4: Enabling GPIO interrupt in MCAL for AM263P4

    Part Number: AM263P4 Tool/software: In this FAQ i will show you the configurations required to enable the interrupts for p ins MCU_GPIO64 and MCU_GPIO63 in MCAL for AM263P4.

  • [FAQ] LP-AM261: Unable to get MAC Port link up with AM261x-LP + Automotive PHY add-on-board (DP83TG720/721)

    Part Number: LP-AM261 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi experts, I am using the AM261x-LP. I am using the automotive-add-on board (DP83TG720/721) on top of the LaunchPad. I have followed all the steps mentioned in the…

  • [FAQ] MCU-PLUS-SDK-AM263PX: Unable to configure Pinmux for RMII for both ports on AM263Px

    Part Number: MCU-PLUS-SDK-AM263PX Other Parts Discussed in Thread: SYSCONFIG Tool/software: Hi experts, I'm using AM263Px with the MCU_PLUS_SDK v10.02. When I enable two MAC Ports and try to select the RMII interface in my networking application…

View FAQ threads