Texas Instruments (TI) Power management support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search power management IC content or ask technical support questions on everything from linear and DC/DC switching regulators to battery management and LED drivers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] How can users re-sequence all rail after they are off due to fault response when the rails’ ON_OFF_CONFIG are set to AUTO mode? UCD90xxx

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90240 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 For rails that are off due to fault response and ON_OFF_CONFIG set to AUTO, the only way to power…

  • [FAQ] What are restart (retry) and re-sequence?

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 Restart only disable-then-enable the faulted rail to see whether it can recover from the previous fault. Restart…

  • [FAQ] What are the fault shutdown slaves?

    Other Parts Discussed in Thread: UCD90120 , UCD90124 , UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90240 , UCD90320U , UCD9090A , UCD90124A , UCD90320 Fault shutdown slaves are the salve rails of the faulted rail. Each rail can have its own fault…

  • [FAQ] How should users implement a power-down sequence when the rails ON_OFF_CONFIG are set to AUTO Mode?

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 Auto Enable means the UCD90xxx device automatically sequences on rails once the device is powered up. It is…

  • [FAQ] Why does the GPI not turn off the rails when it is de-asserted if the GPI is configured as a rail's sequence-off dependency? UCD90xxx

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90240 , UCD90320U , UCD90120 , UCD9090A , UCD90160 , UCD90124 , UCD90320 , UCD90124A Each rail has its own ON/OFF Config setting. In the setting, there are three sources that can control…

  • [FAQ] Is packet error code required by the PMBus master? UCD90xxx

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 It is optional. UCD90xxx devices send and receive a packet error code (PEC) if the PMBus host supports it.…

  • [FAQ] Is clock stretching required by the PMBus master? UCD90xxx

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 Yes. UCD90xxx devices may hold clock low while processing the PMBus inquiry. According to PMBus specifications…

  • [FAQ] TPSM84824: How to calculate FIT rate for this module?

    Part Number: TPSM84824 For modules, the FIT is calculated differently. This is a module assembly made of up individual components (unlike solid state silicon). As such this reliability prediction is based on TR-NWT-332 Reliability prediction model that…

  • [FAQ] TPSM846C24: How to calculate the FIT rate for this module?

    Part Number: TPSM846C24 For modules, the FIT is calculated differently. This is a module assembly made of up individual components (unlike solid state silicon). As such this reliability prediction is based on TR-NWT-332 Reliability prediction model…

  • [FAQ] Why are there no undervoltage faults? For some reason, the rails do not start. UCD90xxx

    Other Parts Discussed in Thread: UCD90120A , UCD9090 , UCD90160A , UCD90160 , UCD90320U , UCD90120 , UCD9090A , UCD90124 , UCD90124A , UCD90320 The UCD90xxx only starts to monitor undervoltage (UV) faults after the rail voltage reaches the Power Good…

View FAQ threads